3RD GEN Protege endlinks, front and rear, NEW!!

I was talking to my mechanic today about my endlinks, and he was interested in designing something himself, but wondering what the demand for it would be. I sent him the lengths 3rd gen Protegs would need, and he will get back to me soon...could be another source for these if Vivid doesn't pan through, or maybe even if they do.
 
Stock length links will fit when lowered, however they will place the anti-sway bar in a less than ideal angle.

Britt
 
So how do you calculate the proper angle, you just need to adjust the endlink so that the bar is flat when the suspension is weighed down?
 
The arms of the swaybar should be parallel to the ground which should be stock endlink length+add the amount of the drop to it.
 
PM bump! Come on folks. I just got word from Agency, and they are monitoring this thread!! :)

Let's show the cool folks over there how bad the ENTIRE community could use these! Just think, if 25 or 50 3rd Gen Proteges were running these, they would more than likely be willing to get into MS3, MS6, and other markets, etc.

Even if you don't have a need for them, let others know about this thread in case they do, please!
 
1. carbonkid (front/rear)
2. bigway (front/rear)
3. CulRidr (rear, front?)
4. Tzar177 (front/rear)
5. boostedprotegelx (front/rear)
6. Protege2886 (front/rear) - pending prices
7.
8.
9.
10.
 
1. carbonkid (front/rear)
2. bigway (front/rear)
3. CulRidr (rear, front?)
4. Tzar177 (front/rear)
5. boostedprotegelx (front/rear)
6. Protege2886 (front/rear) - pending prices
7. Quanttrom (rear)
8.
9.
10.
 
Apparently while my car is at Vivid having dyno/tuning done, Agency Power created a TEST set for me AND installed them!!

I cannot wait to try them out, we have needed this solution for quite some time!

Keep the list growing, folks!!
 
How about a solution for the P5 as well?

1. carbonkid (front/rear)
2. bigway (front/rear)
3. CulRidr (rear, front?)
4. Tzar177 (front/rear)
5. boostedprotegelx (front/rear)
6. Protege2886 (front/rear) - pending prices
7. Quanttrom (rear)
8. CrazyCaker (front/rear) - pending P5 specs
9.
10.
 
that is a 3rd Gen Protege, so sign on, and we can sort out the length differences later, as the design is the same.
 
Joe brings up a good point. You should have a link to this in the MP3 section as well...I noticed you already put one up in the 3rd gen suspension section.
 
i'm down

1. carbonkid (front/rear)
2. bigway (front/rear)
3. CulRidr (rear, front?)
4. Tzar177 (front/rear)
5. boostedprotegelx (front/rear)
6. Protege2886 (front/rear) - pending prices
7. Quanttrom (rear)
8. CrazyCaker (front/rear) - pending P5 specs
9.P5 Rally (rear) - P5
10.
 
Asking for another member; would these (or a modified version of it) fit the AWR bar?
 
1. carbonkid (front/rear)
2. bigway (front/rear)
3. CulRidr (rear, front?)
4. Tzar177 (front/rear)
5. boostedprotegelx (front/rear)
6. Protege2886 (front/rear) - pending prices
7. Quanttrom (rear)
8. CrazyCaker (front/rear) - pending P5 specs
9.P5 Rally (rear) - P5
10. TOprotege member1 - pending prices
11. TOprotege member2 (front/rear) - pending prices
12. TOprotege member3 (front/rear)
13. TOprotege member4 (front) - pending prices
14. TOprotege member5 (front/rear)
15. TOprotege member6 (front/rear)
16. TOprotege member7 (front/rear)
17.
18.
19.
20.
 
Last edited:

New Threads and Articles

Back