this day is pissing me off

Dexter

Banned
Contributor
all this bullshits pissin me off and im here to vent so if you dont wanna listen, click back now and stick your dick in a honeypot.

**** you **** you **** you, **** off, and **** you. go to best buy to get an ink cartridge, douche tells me my card is expired. yes. look at the goddamn raised lettering. well the machine says its expired. fine whatever. eat 12 dicks ill go get cash. so fine, now i have my stupid ink cartridge, so now i can print my data analysis ... i come home and i *thought* i had decoded the RX8 navigation controls data bus. but then i notice all this crazy s***....stuff not following the pattern...each button press has a different leading wave form...sometimes its up for 9ms, then low for 4.5ms, then i press a different button and its up for 5ms and low 10ms. how the **** am i goign to program a PIC to decode that. I'm looking at Dallas One Wire code for the PIC, im going to try to hack that up into something that might work but DOW is a MASTER bus, meaning it only sells the b**** ass slaves to talk when it needs to get data. This Mazda Bus is sorta like I2C i guess, where a device can be both master and slave. But I2C uses more than one line, which makes it hellofa lot easier to decode. this one line bulls*** is ******* irritating. Theres 16 goddamn pins in this harness. and SIX are used. Fuckers why could you use a two wire bus, its not like you dont have the space. I cant believe youd still be reading this far, either. Yes, yes, linkin park, blah blah blah. Oh and malibu, ******* SUCKS. WHO MAKES THIS AND WHY? its like DRINKING WATER.

tired of your bulls***, your online store, your cigs and your sigs, your sponsorship and your stupid forced induction, and your tight curves of your vagina. im sick of it all this. stop complaining about your god damn MSP. ******* sell it, burn it, cover it in gas, jizz on it and then buy something THAT ******* MAKES YOU HAPPY. im going to sit in my ******* basement, gorge my face and watch aqua teen until my feces explodes and hits the wall.





and then ill come right back here and make a thread about it. <3
 
Last edited:
i come home and i *thought* i had decoded the RX8 navigation controls data bus. but then i notice all this crazy s***....stuff not following the pattern...each button press has a different leading wave form...sometimes its up for 9ms, then low for 4.5ms, then i press a different button and its up for 5ms and low 10ms. how the **** am i goign to program a PIC to decode that. I'm looking at Dallas One Wire code for the PIC, im going to try to hack that up into something that might work but DOW is a MASTER bus, meaning it only sells the b**** ass slaves to talk when it needs to get data. This Mazda Bus is sorta like I2C i guess, where a device can be both master and slave. But I2C uses more than one line, which makes it hellofa lot easier to decode. this one line bulls*** is ******* irritating. Theres 16 goddamn pins in this harness. and SIX are used. Fuckers why could you use a two wire bus, its not like you dont have the space

I don't know what the **** you just said little kid. But will it make my MSP faster? This decoder thingy?

Britt
 
Here this will cheer you up Dex
mspsuck.gif
 
Um mr. Dexter, I am not sure if this will make you feel better, but I just walked out on my part time job. (I work at Bennigan's, and that s*** hold does not even know the first thing about treating employees well) All they ******* care about is their damn ******* bonuses. Well bitches keep you ******* ass bonuses, I quite bitches. Left the bastards with 9 ******* tables unattended (I do however feel bad for these people, wrong place at the wrong time). Don't worry I am not a slacker I work full time and go to school full time too. So that was it I left my bad ass uniform on the table in back ripped in half. If you could all do me a favor and never set foot inside bennigan's ever in you life again, I would appreciate it. Thank you all and have a ******* great day.
 
Some whining about the persistance of signals, then about not being a true master-slave configuration (everything is psuedo I2C), and then about only using 5 bits of the two byte input/output registers. What did you expect? This isn't a high-tech microcontroller in these things. And there is no way a master-slave configuration would work with constant external interrupts.

BTW, what the hell are you talking about?:)
 
SP23goesroar said:
everyone here needs to do a group fart. and then relax.

I supposed I poseted on the wrong thread, I am happy that I left my job, by the way, spread the word bennigan's sux, don't give them your money!!!!
 
jurgs01 said:
Some whining about the persistance of signals, then about not being a true master-slave configuration (everything is psuedo I2C), and then about only using 5 bits of the two byte input/output registers. What did you expect? This isn't a high-tech microcontroller in these things. And there is no way a master-slave configuration would work with constant external interrupts.

BTW, what the hell are you talking about?:)

umm are you really trying to help me or are you just ******* around? its cool either way.

There are a total of 3 pins...one is data...two ...i dont know waht they do...one stays high and the other stays low...always....any ideas?
 
Back