xDJ DUBx's 03.5 Pure White LX-T

I've known some hard headed Mexicans but they are on a whole other level.

http://travel.state.gov/travel/cis_pa_tw/cis/cis_970.html

All Americans traveling by air outside of the United States are required to present a passport or other valid travel document to re-enter the United States. This requirement was extended to sea travel (except closed-loop cruises), including ferry service, on June 1, 2009. Starting June 1, 2009, all travelers entering the U.S. by land, sea or air were required to present a Western Hemisphere Travel Initiative (WHTI) compliant document such as a passport or a passport card. While passport cards and enhanced driver’s license are sufficient for re-entry into the United States, they may not be accepted by the particular country you plan to visit; please be sure to check with your cruise line and countries of destination for any foreign entry requirements. U.S. legal permanent residents in possession of their I-551 Permanent Resident card may board flights to the United States from Mexico.

All I can find is re-entering, nothing about leaving.
 
You need a passport to leave the u.s. Ecept for puerto rico since its a commenwealth of the u.s. You can get your passport in 6-8.weeks. If you want it faster its like 200 for 2-4 weeks. You just get a passport right away. You better tell them don't go, cuz you need you birth certifice, two ids, a picture, etc.
 
You need a passport to leave the u.s. Ecept for puerto rico since its a commenwealth of the u.s. You can get your passport in 6-8.weeks. If you want it faster its like 200 for 2-4 weeks. You just get a passport right away. You better tell them don't go, cuz you need you birth certifice, two ids, a picture, etc.

Let me know if u need a coyote man! My in-laws specialize in special escort services!!! :)
 
Just got back from dropping the cold pipe off to get the bpv nipple moved to before the maf, patch the two left over holes, picked up coolant, oil, oil filter, gaskets and clutch alignment tool. Good way to spend $100.

I am now ready to reinstall the motor once it comes back.

You need a passport to leave the u.s. Ecept for puerto rico since its a commenwealth of the u.s. You can get your passport in 6-8.weeks. If you want it faster its like 200 for 2-4 weeks. You just get a passport right away. You better tell them don't go, cuz you need you birth certifice, two ids, a picture, etc.

Dude, I've been trying all ******* morning. Mother fuckers don't wanna listen. Best case scenario, they get turned away at the boarder, worst case, they let them out but not back in.
 
mexico might refuse them, but then they would still have to go back through us customs, where their citizenship would be checked. hopefully they at least brought birth certificates or they will have a really long wait. if they dont plan on flying ever, they could get a passport card. it is cheaper than a passport, but only good for places you can drive to basically.

funny thing is, when you go to mexico... you deal with mexican laws. when you come back into the u.s., you deal with our laws. they arent the same.
 
Well she came back yesterday, but after spending a few hrs at the boarder. They all had birth certificates and SS# so they let them pass after a full inspection, thank god. She told me 6 cops had been killed the night she stayed there, in the area they were in.
 
On an on topic matter, looks like I'm going to be doing a retrofit. lol.

After talking to Matt and getting prices, the lights are more than affordable if I do the labor myself. FX-R Bi-Xenon projectors w/ E55 Shrouds, CCFL Angle Eyes and Philips 85122+ D2S bulbs. Also gonna run my halogen highs off a switch instead of the harness since the projectors will be Bi-Xenon, probably with hids just to add more of a crazy factor. lol.

This is mos def gonna be the next project once this swap is done and over with.
 
Seriously. lol.

I'll figure something out once I start ordering parts and what not, gonna buy some ebay sedan lights for the lenses, swap them out with mine, then throw the sedan lights on while I work on the p5 lights.
 
Back