TX Meet Dyno Results
- Thread starter JDM Sam
- Start date
TX Speed Demon
Member
I AM THE LOWEST YEAH!!!!!
138 whp 144 lbs
03 MSP - unflashed
HIboost FMIC
Perrin SRI
Apex catless downpipe
5psi (stock)
Air/Fuel was pegged at 10 (lowest registerable signal) from 2800-5300 RPMs 10.8 from 5300-6500
I have video of the run, but it's 8 megs and won't upload. I'll try to resize on Monday when I get to work
138 whp 144 lbs
03 MSP - unflashed
HIboost FMIC
Perrin SRI
Apex catless downpipe
5psi (stock)
Air/Fuel was pegged at 10 (lowest registerable signal) from 2800-5300 RPMs 10.8 from 5300-6500
I have video of the run, but it's 8 megs and won't upload. I'll try to resize on Monday when I get to work
Attachments
Last edited:
(confused)TX Speed Demon said:
TX Speed Demon
Member
^^ tell me about it. Funny thing is I have raced and beat some of the cars there that dynoed in the 150+ range. But when I race I don't do it at full throttle till after 4K rpms so I don't get the hesitation. But when they do the dyno runs they floor it at 2500 RPMS and keep it that way till they let off, so major hesitation + low boost (5psi) = low output numbers. Just goes to show dyno sheets aren't always a good/accurate representation of drivable power.
Last edited:
TX Speed Demon
Member
Jake said he was going to give it to you to give to me. You don't have it? I assume he'll drop it your way next time we meet.
Stock as they come!!!!
Per Sam's orders, I am posting my Dyno results in here.
Bone Ass Stock!!!! not even a guage
157.46 wheel horsepower and 166.87 torque and now for my over use of smilies that I am so known for!!!! Take up that bandwidth!!!
(thumb) (humpleg) (alright) (headbang) (yes) (eek2) (boom04) (rockon) (yippy) (shocked) (cabpatch) (wiggle)
(lol2) (2thumbs) (laugh)
Per Sam's orders, I am posting my Dyno results in here.
Bone Ass Stock!!!! not even a guage
157.46 wheel horsepower and 166.87 torque and now for my over use of smilies that I am so known for!!!! Take up that bandwidth!!!
(thumb) (humpleg) (alright) (headbang) (yes) (eek2) (boom04) (rockon) (yippy) (shocked) (cabpatch) (wiggle)
(lol2) (2thumbs) (laugh)ELEmental59437
Member
- :
- 2002 P5, 1978 F250
I dyno'd at 0 HP (at the wheel) and 0 ft lbs of torque... thanks to not having a clutch in my car... thank you thank you... I will post the invisible dyno for those who dont believe me... kthx..
BlueSolrac
Member
- :
- 2004 Mazda 6i
505zoom said:
No Jake did. 217 and 216 tq I believe. He revved to only 6000 RPMish till his stock BPV popped loose and all boost went kaput. Equinox put out a # in the 200s also. I think they were the only 2 Protegs to eclipse past the 200 hp mark along with the Mazda 6. So there's your Top 3 dyno'd cars.
Last edited:
actually i checked again, 5700rpm it lost boost... DAMN STOCK CRAP.
ok done venting now. but 217/217 at 5700, and still climbing up up and away. we're calling it safe at 230/230, and i dont even have a front mount. hahahahahahaha
300 this summer!!!!!! MUAHHH
so declare me da king
ok done venting now. but 217/217 at 5700, and still climbing up up and away. we're calling it safe at 230/230, and i dont even have a front mount. hahahahahahaha
300 this summer!!!!!! MUAHHH
so declare me da king
1stgensupercar
Member
- :
- 92 protege dx
1stgensupercar
Member
- :
- 92 protege dx
i need more cash to do that
gimpo2 said:
ELEmental59437
Member
- :
- 2002 P5, 1978 F250
Gawd, another dick measuring contest.. you KNOW I would have been the king if I had been able to bring my car. I could push 250-260 EASY with nothing like a stupid BPV screwing it up.... or loosing spark.. or anything..
