Own an AWR rear swaybar? Look inside, trust me, its' good.

[Mad Hatter]

Bolts came today, thanks, alot!!

 

[t3ase]

PR5Matt, I'd advise you not to act up like that again. You're needlessly bashing this sale. Thanks

 

[glyph]

I just did the same thing for some hex cap screws (larger) that came with my MAM kit. Anyone interested in those, too? Mine came with a set of 9, larger hex cap screws. By my measurements they are 3/8" thread width, 1" thread length, 1/2" diameter cap, ~1/4" depth cap.

$7 for a set of 9!

 

[glyph]

PR5Matt, I'd advise you not to act up like that again. You're needlessly bashing this sale. Thanks

Thanks.

 

[glyph]

oops, I just checked the bag of screws, and found that there are 3 different lengths... I have replacements for two of them. The other two lengths I will look into getting tomorrow. I do still have the two replacements...

My measurements were wrong, too, can't figure that one out...

For the record, the list of measurements:
2 each 5/16" thread width, 3/4" thread length, 15/32" diameter cap, 5/16" depth cap
2 each 5/16" thread width, 5/8" thread length, 1/2" diameter cap, 5/16" depth cap
5 each 5/16" thread width, 1" thread length, 1/2" diameter cap, 5/16" depth cap

 

[fluke22]

Mine were rusted just a few weeks after installation! Great idea glyph, keep up the good work.

 

[glyph]

thanks, my hearty supporters! all have been shipped now except yours fluke. They're packed and ready to go.

 

[Pretzellogic]

Got them yesterday. My GF couldn't understand why I was excited to recieve "A couple of screws"

Thanks again for helping out those of us who can't find the damn things.

 

[JCell]

patiently waiting, hasn't rained yet so (cool)

 

[JCell]

i just got mine, they so shiny

 

[glyph]

glad you guys enjoy them. I didn't think there would be so many takers.

 

[SpecRacer17]

Got any more of those things!

 

[glyph]

yep

 

[Foolish]

I went ahead and subscribed to this, so that when I get the endlinks, I can order up these bolts and install it with stainless from the start.

Oh, and thanks for going to the trouble, Glyph!

 

[glyph]

you could just order em now, in case I run out later...

 

[ARD MP5]

This is great. You guys are a compliment to any enthusiast community. This is very nice of you. If i orderd some I'd throw you a couple extra bucks just for taking your time and being a cool guy. I'm sure there are people in remote places that won't find em for some reason and the gas to get them would be more than five dollars. lol.

Mad props and if I had a 21.5 I'd get em from you even tho I can get em here.

Laters, Rishie

 

[SpecRacer17]

Are the screws the same for the 19mm AWR rear sway? If so I'll take'em!

 

[glyph]

This is great. You guys are a compliment to any enthusiast community. This is very nice of you. If i orderd some I'd throw you a couple extra bucks just for taking your time and being a cool guy. I'm sure there are people in remote places that won't find em for some reason and the gas to get them would be more than five dollars. lol.

Mad props and if I had a 21.5 I'd get em from you even tho I can get em here.

Laters, Rishie

thanks, Rishie, much appreciated.

 

[glyph]

Are the screws the same for the 19mm AWR rear sway? If so I'll take'em!

dunno, I have to check. I am guessing so... but I'll email Tony and ask.

 

[glyph]

here's what I got back (fast response):
The clunking is usually caused by loose bolts or metal to metal contact between the rod end and the surrounding metal cone washers or the anodized clamp. This can be cleared up by the use of a newer style rod end that we now supply w/ "o" rings to support and the use of a nylon lower cone style washer instead of the steel one. Yes the bolts are the same 1/4 20 socket head cap screw. I hope that answers your questions.

tony / awr

oh yeah, I also asked about the clunking.