Wagonbacker9
Member
- :
- 2004 'Hoe
you sure your clutch isn't gone? theres no way you're spinning in 4th on dry pavement.
What have you done to your MSP today?
- Thread starter baconbitz
- Start date
onlinemazdaparts has them for $7 each plus shipping
Wagonbacker9
Member
- :
- 2004 'Hoe
posting this without a link is just mean.
theyre not too hard to find, onlinemazdaparts.com, search for the 2003 tribute and find the washer nozzles
Wagonbacker9
Member
- :
- 2004 'Hoe
that was the missing piece... thank you! lol
Ricktalife
Member
- :
- 2012 Subaru WRX
Noted. Thank you.
Outlawstar98
Member
- :
- 2003 MazdaSpeed Protege / 2013 BRZ
Removed more bolts from my motor... ITS ALMSOT OUT! 
just like 1-2 bolts left then the trans and block is disconnected and it can be pulled.
just like 1-2 bolts left then the trans and block is disconnected and it can be pulled.SeR_Cyclops
Member
- :
- Mazdaspeed Protege
How come you didnt bring the motor and the tranny out together?
snake_eyes
Member
- :
- 2003.5 Titanium Grey #????
Put in GlowShift A/F gauge, boost gauge, and voltmeter... But, while replacing all the vacuum lines the nipple broke off my BPV :'( Was planning on replacing it when I put in hard pipes it just might be sooner than later.
I have a Forge WGA to replace also but right now feeling low. (bang)
Problem is that thanks to my big mouth and complaining to Mazda Canada about the local stealership I am going to have to look elsewhere for parts or get the wife to order them for me!
I have a Forge WGA to replace also but right now feeling low. (bang)
Problem is that thanks to my big mouth and complaining to Mazda Canada about the local stealership I am going to have to look elsewhere for parts or get the wife to order them for me!
Outlawstar98
Member
- :
- 2003 MazdaSpeed Protege / 2013 BRZ
I dont need the tranny out, just makes it easyer for reinstall.
i went to mazda today and was looking to get some factory exhaust gaskets to cut the inside out of for my apexi n1. they are like $9.50 a piece! and i need 4! rock auto here i come!
but while i was there i asked about a exhaust manni. mine is cracked but i will try and get a steedspeed or thunder manni. but anyways long story short, the factory manni is still $1780!!!!
but while i was there i asked about a exhaust manni. mine is cracked but i will try and get a steedspeed or thunder manni. but anyways long story short, the factory manni is still $1780!!!!
Outlawstar98
Member
- :
- 2003 MazdaSpeed Protege / 2013 BRZ
Just picked up my front 2003.5 lip from my friend. about time. haha
TheDirtyGoatee
Member
- :
- 2008 Mazda MX-5 5MT PRHT
1 question, 1 point.
Question: Can you run the car without a BPV (n00b question I know) and what's the dangers? (by no BPV I mean, plugging the hole up or running it open) I'll explain why I ask when I'm answered (no I am not currently running this setup).
Yeah, I priced a new steering wheel for the MSP. Still nearly 1000 bucks. Priced a P5 wheel, just over 700 bucks. Then I priced an MSM wheel since it's a similar design... over 1000 bucks. My wife wants me to have an airbag otherwise I'd scoop up an aftermarket wheel. Anyone know someone who's selling a stock MSP wheel, P5 wheel, MSM wheel, or 2004 ish Miata wheel for relatively cheap? I have the airbag module. My wheel looks like ass where Mazda decided to paint the wheel.
justanothermp5
Banned
- :
- Rust Bucket
with a hole, you cant boost and will probably stall alot
with a plug you will just get compressor surge but then you need something to cap the vacuum line so u dont have a leak
with a plug you will just get compressor surge but then you need something to cap the vacuum line so u dont have a leak
TheDirtyGoatee
Member
- :
- 2008 Mazda MX-5 5MT PRHT
What if you indeed cap the vac line?
Wagonbacker9
Member
- :
- 2004 'Hoe
yeah, sure, you can... and you'll probably smoke your turbo in 10K miles. rally cars do it, because then they don't lag between shifts, its just HORRIBLE for your turbo. you keep stuffing air in the charge pipes when the throttle is closed... imagine the stresses of you trying to breath out into a plastic bottle with a 1/8" hole in it... thats what you're asking your turbo to do.
TheDirtyGoatee
Member
- :
- 2008 Mazda MX-5 5MT PRHT
Cool. I had a coworker tell me he did this with his Eclipse. He said it's better than a blow-off valve... (rlaugh)
