What have you done to your MSP today?
- Thread starter baconbitz
- Start date
Perro del Sol
Member
- :
- 2003 MSP, Spicy Orange, 2004 Mazda 6 Hatch, 2004 Mazda 6 Wagon
Sounds like good advice from 20t03speed is offering you some good advice and lower the boost! Knowing these motors have limitations, why push it? If you want a Speed 3 trade it in now and move on.
- :
- 2003 Mazdaspeed Protege 1660, 2004 Winning Blue RX8, 2005 Mazda6
These motors have limitations!?!?! I'm well aware of the "limitations"... I have a pile of parts/blocks out in my shop right now... lol
Last edited:
- :
- 2003 Mazdaspeed Protege 1660, 2004 Winning Blue RX8, 2005 Mazda6
If I had an extra engine, I'd totally build it, but after grenading my back up, then another engine I'm fresh out.
I'm totally thinking about getting a Water-Methanol kit- Snow stage II... Anyone other than Joey using Water/Methanol injection?
I'm totally thinking about getting a Water-Methanol kit- Snow stage II... Anyone other than Joey using Water/Methanol injection?
Last edited:
2.0t03speed
Member
- :
- 08.5 CWP Speed 3
He likes to live on the edge.
- :
- 2003 Mazdaspeed Protege 1660, 2004 Winning Blue RX8, 2005 Mazda6
The edge of harmony and chaos... Though, most often I fall off into chaos which is accompanied by destruction...
- :
- '13 CWP MS3 & '16 Mazda6 GT
The edge of stupid...
- :
- 1989 RX-7 GXL Blaze Red
(thought)
- :
- '13 CWP MS3 & '16 Mazda6 GT
Don't give me the frowny face....if anyone here should know better...it's you LOL
- :
- 1989 RX-7 GXL Blaze Red
I like my gates stuff
Perro del Sol
Member
- :
- 2003 MSP, Spicy Orange, 2004 Mazda 6 Hatch, 2004 Mazda 6 Wagon
Mishimoto Radiator installed, have to re-route my cold pipe after removing the the OEM Radiator because the old piping would not allow the radiator to fit. So a new elbow is going on the FMIC and then we will do a mandrel bend to get pipe back to the throttle body, as I don't link have all those couplers on the piping. Should have it done by today.....
- :
- 1989 RX-7 GXL Blaze Red
Exciting!!!!!!!
Perro del Sol
Member
- :
- 2003 MSP, Spicy Orange, 2004 Mazda 6 Hatch, 2004 Mazda 6 Wagon
She is done and I will have her back when I get off work......All I have to do next is get the AWR rear sway on Saturday and have the Hooisers mounted on the RPF-1's....
Maiello169
Member
- :
- Mazda, Protege, Speed
P.E.P. downpipe just arrived at my front door!!! super excited... even though my car still isn't working..lol
[/IMG]
Where did you order that from? how much do those go for ?
Maiello169
Member
- :
- Mazda, Protege, Speed
So after getting rid of the P0171, now im getting an exhaust leak code, it must be a small leak, ill clear it and then it comes back on after 40 miles ... im thinking one; it couyld be from when i had my SLS mid-pipe put in, they didnt use a gasket they used exhaust adheasive instead ... what is the correct gasket that conects to the mid-pipe to the rest of the exhaust ? im guessing they used that other stuf because i didnt get the correct one ...? any thoughts?
- :
- 2003 Mazdaspeed Protege 1660, 2004 Winning Blue RX8, 2005 Mazda6
An "exhaust leak code" doesn't exist...
That is a Pope downpipe, no longer in production. Just had a final run of 25 units and they're done. There may be another vendor taking over production, but that's not definite yet.
That is a Pope downpipe, no longer in production. Just had a final run of 25 units and they're done. There may be another vendor taking over production, but that's not definite yet.
