Wagonbacker9
Member
- :
- 2004 'Hoe
camber doesn't wear tires as fast as bad toe... either way you really would probably want to get it professionally aligned.
What have you done to your MSP today?
- Thread starter baconbitz
- Start date
- :
- 2002 Honda S2000
overheated like crazy on a short drive to the other side of town. really?! gah!!!
http://www.mazdas247.com/forum/showthread.php?t=123758016
http://www.mazdas247.com/forum/showthread.php?t=123758016
they didnt look bad at all actually.. maybe a little worn thats all. they've been clunking for the last 2 years when the temp outside was colder.. i dont think they were ever changed before, so they had 80k on em lol
Wagonbacker9
Member
- :
- 2004 'Hoe
installed my GTSpec front lower tie bar, must be one of the later ones, as it cleared the frame easily... but it was orange. Brand new parts for used prices rock.
oh, and put the snow tires on today. yuck.
oh, and put the snow tires on today. yuck.
Anyone know where I can find better feed lines for the GT28RS? I can't seem to find anything on them, and I'd prefure something better than the weak stockers.
EDIT: A stock water feed line is $178 at the dealer, this is one reason I'd like something new.
EDIT: A stock water feed line is $178 at the dealer, this is one reason I'd like something new.
- :
- 03.5 YLW MSP
Did a boost leak test and fixed a few leaks. As well as tweaked my bumper fitment so it doesnt sag as much.
- :
- MSP 1145
Just put away the MSP for winter. Now driving the 2000 caviler beater. Woo Hoo
YUCK.
lol. i swapped out the msp rad for a full length pro one. ran for a few hours, idled, stop and go.. doing well. no overheating. i kinda like it better too. fits better if you ask me!
TheDirtyGoatee
Member
- :
- 2008 Mazda MX-5 5MT PRHT
*looks at Bandar's new sig*
Mazda's are happy cars.
Mazda's are happy cars.
Velocifero
Wham Bam thank you Ma'am
- :
- VRM MS6, Sunlight Silver MSP
Got new pads and rotors yesterday, now only if I had time to do anything with the car. I haven't even driven it since Sept 30th. I started it the other day with my son in my lap, but need to do some work and then emissions and get the tag updated, I should have never gotten a second vehicle, now I don't work on my car because I don't need it to get around.
Wagonbacker9
Member
- :
- 2004 'Hoe
GTSpec installed, test fit FD wheel, from a few days ago
and this went on just now:
BEFORE:
AFTER:
and this went on just now:
BEFORE:
AFTER:
- :
- MSP 1145
not sure about the fd wheels. but everything else i like!
Wagonbacker9
Member
- :
- 2004 'Hoe
just wait til spring....
- :
- 2002 Honda S2000
what are the specs on those wheels again?
Wagonbacker9
Member
- :
- 2004 'Hoe
i read that they don't fit the hubcentric, but they fit better than my mz3's and my P5 steelies... notice how it sits there with no lugs on? neither of my other sets will do that.
I have 3mm spacers if I need em for clearance, but I'm hoping not to use them. The rim is VERY close to the strut.. if the tire bulges, I think it'll contact. didn't check the fronts yet, as I'm not really worried.
16x8, +50 offset, 13.8 lbs for the non reinforced, 15.4 lbs for the reinforced version (weights may be slightly off...) I have one pair of each.
they're not the prettiest (in some ppl's opinions) but the performance aspects canNOT be beaten for the price anywhere.
I have 3mm spacers if I need em for clearance, but I'm hoping not to use them. The rim is VERY close to the strut.. if the tire bulges, I think it'll contact. didn't check the fronts yet, as I'm not really worried.
16x8, +50 offset, 13.8 lbs for the non reinforced, 15.4 lbs for the reinforced version (weights may be slightly off...) I have one pair of each.
they're not the prettiest (in some ppl's opinions) but the performance aspects canNOT be beaten for the price anywhere.
Last edited:
