BEFORE ATTEMPTING THIS: I WILL NOT BE RESPONSIBLE FOR YOUR ACTIONS, EVEN IF RESULTING IN INJURY TO YOU OR TO YOUR CAR, SO PLEASE READ AND UNDERSTAND THESE INSTRUCTIONS CAREFULLY AND MAKE SURE YOU UNDERSTAND THEM CLEARLY BEFORE BEGINNING, PLEASE I WOULD HATE FOR YOU TO MESS UP YOUR EXPENSIVE TOY! ALSO GET THE CORRECT PARTS/TOOLS, BELOW IS A SUPPLY/TOOL LIST:
1)Small, very small flat blade screw driver, or equivalent
2)wire cutters/crimpers
3)electrical tape
4)female and male spade connectors 16-18 gauge size, small/narrow and big/wide ones. check your parts stores. you will see what size later in the instructions when you remove the wires from the harnesses.
5)approx 15-20" of wire preferably 16-18 gauge
6)Possibly a pair of needle nose pliers for removing/installing the wires in the harnesses.
7)approx. 45-60 minutes for a good clean install.(trust me it pays off in the end with the look of the lights and the much better quality job, rather than cutting up the wires of your baby)
ok guys i have done this mod and i will tell you how to do it cleanly and easily and can be reversed in a matter of minutes. All you are doing is replacing the turn on wire for the relay, instead of getting power from your headlight power you are getting it from the illumination power for the gauge lights (im assuming) although that doesnt matter as long as the relay gets the voltage to open and turn on the lights.
Ok with that said, here is how i did it:
1)Open the drivers door and remove the panel on the side of the dash, it helps to reach under the dash and push out on it, on the part closer to the driver (not the door hinge side, it slips in the groove).
2)Locate the relay-its under the dash by the clutch pedal, there should be like 3-4 small black boxes, locate the one for the fog lights by turning them on and off while listening closely/and or feeling. I had to listen and feel as all the relays look the same.(Small black boxes for those who dont know).
3)locate the back of the foglight switch.
4)start by removing the harness from the relay and the foglight switch.
5)on the harness removed from the relay start by using a very small flat head (blade) screwdriver or equivalent, remove the (Red, larger wire) wire, by pushing on the small metal clip inside the harness, look closely and you will see how it is held in there, its not as difficult as it sounds, i promise.
6) Using the same procedure as above (5) do the same in removing the (green/black) wire from the harness that plugs into the foglight switch.
7)once both are removed this is where the fun begins, start with a short peice of wire, approx 8-10" long. On one end crimp on a female spade connector, this will be inserted back into the harness going to the relay, where you removed the wire in step 5.
8) tape the end of the wire removed in step 5 so no shorting occurs , also tape it to another loom under the dash so it doesnt dangle.
9)ok pay attention here, on the other end of the wire in step 7 attatch another short peice of wire approx 5" long by twisting them together, crimp them together with another female spade connecter.
10) on the other end of the short wire in step 9, crimp on a male spade connector.
11)ok now the connecting wire should be complete, take the remaining female connecter and put it back in the foglight harness where you removed the one in step 6(green/black wire).
12) this should leave you with the wire you removed from the foglight switch in step 6 (green/black) and a short piece of wire with a male spade on it (created in step 9).
13) the wire removed from the foglight switch in step 6 should have a female spade on it, take the male spade on the short wire that you created in step 9, and plug it into the female spade removed from the foglight switch in step 6, (the green/black) wire.
14) tape all remaining exposed connections (should only have one) and voila you are done, the fogs come on with the parking lights and with the headlights and the fog swith is still functional.
ATTENTION !!!- I made a typo in the little graphic, on the very bottom right caption where it says "you removed the red wire, and the green and black wires" it should be " you removed the red wire and the green/black wires, as in the red wire from the relay harness and the green&black<--- (1) wire from the fog switch. And also try and find the appropriate size spade connectors, as they have smaller and larger ones-narrow and wide, so pull em out and see what you need before beginning.
I will attach an image of the jumper wire i created, this will be a paint image not a actual image of mine, it is 1:00 am here, youre lucky you are reading this!
If any more detailed info is needed(it shouldnt be) then shoot me an email.
Mike