FS: DaveB Ring Clones

Status
Not open for further replies.
sort of. if replacements are made you can get one, but thats been ongoing for 3 or 4 months now and hasnt come to fruition yet. im not able to access the machines to do them, and someone is trying to do some as a favor to me... its just going very, very slowly.
 
back from the dead - the TA is still working on it. he ran a revised ring where i adjusted the... uh... rake angle of the sides, and it came out great.
not bad considering i dont have tools, rings, a cluster, or the machine to run it on, and just went by memory.

hes working on running these newest rings which should substantially reduce the infamous ring gap and fit about as snug as the smaller rings. sounds like its not perfect, but its a big improvement.
 
i went to troy to see whats been going on, and the results arent encouraging. im pretty annoyed since if i knew it was going to take 6 months to end up where i left off, i would have done something else. theres not a lot of consistency, and despite my training him with how to use the machine and make sure everything works correctly, he still hasnt "gotten it". simply put, understanding how to troubleshoot the issues is still over his head for something this complex.
its not all his fault though - theres a lot of people who use that machine and that shop, and since its a beginners shop they have a nice way of chipping tools, changing coordinates, and doing things on the machines without knowing how to undo them. i would generally know how to fix them and go right back to consistent runs, but it doesnt seem like hes at that stage yet.
im still going to let him run down the stock at his leisure, but im not expecting much. he got an updated program which has been turning out rings that are more consistent, but based on what ive got in my lap here... i dont know about my faith in him to correct something if it goes astray.

FORZWIN, i have two rings for you for all your patronage, patience, and assistance with testing the other rings. they are unfinished, and still have sharp edges. rub them down with some 110 grit and you should get close. these are the first two off the new program and are of equal quality to mine. please PM me your address.

i have a few others which arent as nice as id otherwise distribute but sadly this might be the only option. if you are interested in any, please PM me your address. i will cover shipping for any of these replacements, but if another batch is offered later (i.e. from the revised program) you will be responsible for stock and shipping costs if you want another replacement. none are sanded or brushed, but it takes about 5 mins with some 110 grit to get them looking good.
-- two of the "older style" ones. these either came from FORZWIN, or were two of the last ones i had laying around at the shop. they fit my cluster pretty well and look good, but if they did come from FORZWIN his ran a little small. your mileage may vary, you might need double sided tape, i dont know.
-- three are oversize and definitely wont move in the cluster, but they might stick out to the point that your center clip on the cluster shield wont lock. you could grind the edges a little to get them to drop in further, ignore the clip, or whatever. the profile is somewhat "off" - they sit a little tall.
-- one is "just right" - fit is a little snug, but overall its a production quality piece
-- two more are WAY oversize (.015"+). these would DEFINITELY require grinding - sanding wouldnt fix the problem. i would encourage you not to take these unless no other ones are available and you have the tools to fix them.

let me know guys... im doing what i can for you here.
 
got it. just an FYI for everyone, the four revised rings are all spoken for. i will be sorting out shipping details tonight.
 
hey guys,
ive been super busy lately and have barely found time to check my email, let alone put everything together for this. im hoping i will get everything figured out tomorrow or thursday.

sorry for the wait...
 
so i have someone local who gave me a hand with the project previously, im going to be meeting up with him to test fit the rings as i no longer have my car, and the cluster i was using for testing is pretty beat up. we were hoping to do today, but it ended up getting snowed out. we have tuesday penciled in.

again - sorry to add to the wait, but i figure you all would prefer rings that fit.
 
yeah sorry about not meeting up on friday. drive home was miserable enough at 4 and prob would have been much worse if i had waited around to work on the rings.

tuesday for sure!
 
i dont want to call the project dead, i still think about it way more than i should be, but the TA stopped replying to my texts. the other rings werent as consistent as i would want to ship them out, and i planned to re-do all the programming for the lathe again.

problem is, i cant do even that much right now if he cant give me a reliable measurement from some of the parts.
anyways, im considering taking all my s*** from him and getting estimates from professionals. im pretty irritated that it took him the better part of a year to do nothing but waste my time, money, and stock. im sorry its taken so long, but at this point, im not sure i would get my hopes up for anything coming out of this.

if you still want something you might be able to salvage, send me a PM with your address and ill try to mail a few out when i get the chance. unless yours is rattling around in the cluster and is so hosed it cant even be taped down, im not sure these will be an upgrade. ill do what i can, and i will try to get the job quoted, but its been a major disappointment going this route... i can say that for sure.
 
So can you still get gauge rings for a protege? Really wish I snagged my daveb rings off my protege when I sold it.
 
Status
Not open for further replies.

New Threads and Articles

Back