CX-5 Photos - Share your shots with us!
- Thread starter inodes
- Start date
Chris_Top_Her
Contributor
- :
- San Antonio, Texas
- :
- '15 CX-5 Miata AWD
Boss
Chris_Top_Her
Contributor
- :
- San Antonio, Texas
- :
- '15 CX-5 Miata AWD
Yes. It's a Danish guy in the CX-5 club face book page.
Loaded up I imagine that is close to the EU towing limits. I personally wouldn't feel comfortable towing a trailer of that size with my CX-5. Towing my 14" boat in the wind is noticeable... I can only imagine the white knuckle drive even at 35MPH with that behind you.
Boss
I wish we could have the diesel over here in the states. With the whole VW diesel-gate incident, I don't think that will be happening anytime soon.
Like the setup alot. Was thinking about that type of blue before I went with my color scheme. Are you lowered?Here is my current setup - great for hauling bikes and scooting around.
Sent from my iPhone using Tapatalk
Sent from my XT1254 using Tapatalk
Thanks for the kind words. I was lowered on H&R's but wanted a bigger drop so installed some Corksport springs - current ride height as seen in the photo.
Here is my current setup - great for hauling bikes and scooting around.
Sent from my iPhone using Tapatalk
Mind if I suggest something? Well 2 things now since I saw something else since starting this post.
Have you considered removing the plasti-dip from the inside the mazda logo? You can remove it without removing it off the emblem with a toothpick. Once it starts to lift up a piece, you just pull on it.
The other was also plasti-dipping or removing the skyactiv emblem for consistancy. You removed the CX-5 part, so clean on both sides would work, you blacked out the mazda logo, so black for both would work. I know it isnt my car and its your style that matters, so just a suggestion, take it or leave it.
Here it is with the center of the mazda logo removed of plasti-dip and the skyactive plasti-dipped in the same color as your car
Mind if I suggest something? Well 2 things now since I saw something else since starting this post.
Have you considered removing the plasti-dip from the inside the mazda logo? You can remove it without removing it off the emblem with a toothpick. Once it starts to lift up a piece, you just pull on it.
The other was also plasti-dipping or removing the skyactiv emblem for consistancy. You removed the CX-5 part, so clean on both sides would work, you blacked out the mazda logo, so black for both would work. I know it isnt my car and its your style that matters, so just a suggestion, take it or leave it.
Here it is with the center of the mazda logo removed of plasti-dip and the skyactive plasti-dipped in the same color as your car
Appreciate the suggestions!
There isn't Plasti-Dip inside the Mazda logo - I had laid down a little carbon fiber vinyl so it peeks through the blacked out emblem. Hard to see in the photo - sorry!
I was going to remove the Skyactiv emblem, but I kinda liked it there as it represents the philosophy of the brand. Thought about blacking it out too, but the letters are inset and black so it would make it a little more obscure. So I just left it as is. Might change my mind and black it out and go with a contrast color on the lettering in the future, but we'll see.
Thanks again for the feedback!
Sent from my iPhone using Tapatalk
Here is my current setup - great for hauling bikes and scooting around.
Sent from my iPhone using Tapatalk
Dig the color combo!
Sent from my iPhone using Tapatalk
New shoes for new adventures!
Sent from my iPhone using Tapatalk
I like the adventure semi-rugged look of the tires/wheels.
Chris_Top_Her
Contributor
- :
- San Antonio, Texas
- :
- '15 CX-5 Miata AWD
New shoes for new adventures!
Sent from my iPhone using Tapatalk
Cool pic. Are you on the cx5 club USA Facebook page? We are looking for a new cover photo, and yours would be a good entry.
