Broke a washer nozzle

[Diehonda]

You guys may want to try the Toyota ones as well, they have 3 holes instead of 2.

Which Yota, because mine don't and I have had six of them.

 

[Dimitrios]

You can try Ford Escape/Tribute nozzles too (if you're at the dealer anyway).

 

[ke20sprinter]

go to the junkyard & get a pair to match

(would cost you a few bucks entrance fee only, if you stuff them in your pocket) (wink)

WiL

 

[ottawaP5]

Which Yota, because mine don't and I have had six of them.

The 03 and up Corollas and Matrix

 

[Diehonda]

The 03 and up Corollas and Matrix

OK, haven't gotten one of those yet. I actually looked at a couple when I got the 5.

So:

03+ Corolla
03+ Matrix
2001 - 2004 Focus

Any others? This could really help someone down the road.

 

[mcstark]

You guys may want to try the Toyota ones as well, they have 3 holes instead of 2.

3 holes instead of 2???

Guess it depends on the girl...(cabpatch)

I'll keep you all updated on the nozzles...headin' to the Ford dealer today.

 

[RaiderMS3]

I'll keep you all updated on the nozzles...headin' to the Ford dealer today.

yeah, if they fit, sweet, good mod.

 

[aMaff]

subscribing for into on nozzlez

what he said... (boom03)

 

[Kansei]

This is freakin exciting *subscribes*

I wish this thread was there in the summer when I replaced my CF hood with an OEM hood and had to buy the new washers from the dealership.

 

[Lord_Zath]

yeah I really want to change out the stockers to the misting type if possible

 

[mcstark]

OK...just came back from the Ford dealer. For those playing along at home:

The left and right side are the same part #...17603. Cost me $6.63 apiece. I checked under the hood of our cars and the male end on the nozzle is shaped differently (take that comment in any direction you like (boom03) ). The Mazda one comes straight down, while it looks like the Ford one goes in toward the windshield. They needed to order them for me, so they should be here tomorrow. I'll let you know how different they look...I doubt I'll have any problems.

If it works out fine...I'll be checking out the one behind the rear spoiler. Ford makes two kinds - one for the hatchback (ZX3) and one for the wagon. But that may just wait until Spring/Summer.

 

[maltodextrin]

Have you tried a cow magnet? Y'know, those little round ones. They're pretty powerful.

^ This gave me an idea for my CF hood...

 

[Canecreekfreak]

subscribing.

Is aiming them just a matter of getting the nozzles to move? I tried moving mine w/a small safety pin the other night (it was outside and below freezing), and they didn't move at all. Just bent the pins. My drivers side nozzles spray too high, and the pass. too low.
(screwy)

 

[mcstark]

subscribing.

Is aiming them just a matter of getting the nozzles to move? I tried moving mine w/a small safety pin the other night (it was outside and below freezing), and they didn't move at all. Just bent the pins. My drivers side nozzles spray too high, and the pass. too low.
(screwy)

Yeah, that's all you need to do...but it's difficult at best. When I do get them to move, they usually move waaaay too far.

 

[altspace]

All this for a washer nozzle? Funny.

 

[ottawaP5]

I just bought the replacement nozzle.....$6 at the dealership...pretty cheap!

 

[ottawaP5]

subscribing.

Is aiming them just a matter of getting the nozzles to move? I tried moving mine w/a small safety pin the other night (it was outside and below freezing), and they didn't move at all. Just bent the pins. My drivers side nozzles spray too high, and the pass. too low.
(screwy)

Spray the ends with silicone..the rubber will soften and they will move way easier.

 

[MyZmZm]

^These are the ford ones you're talking about, right Phil? Or did you just get the mazda ones again?

 

[stra]

mazda protoge for sale

hi
i am selling a mazda protoge
1)mileage-240,000
2)4 seater
3) passed emission test
4)good condition
anyone who is intrested should call 7766778
0r 8427981
ask of albert or ben

 

[Lord_Zath]

several things, mr. stra.

1. don't post crap in other people's threads unless it's on topic. Do not post further in this thread or other threads or I will have the posts deleted. Create your own post but see #2 first.

2. follow the forum rules. see the link in my signature.