shane02pro5
25ish_psi
- :
- New Caney TX
Not without swapping out the transmission, wiring harness and ecu which would be quite alot of work!
What have you done to your P5 today?
- Thread starter Tg5
- Start date
boostedprotege
Member
- :
- 2003 mazda protege dx/2003 mazda protege5
jist paid off the p5!!!!! woooohooooo
just thinking of getting the rear quarters done by pro. And after that im done putting stuff on the car. Just to look clean. I cant help but think about that rust thats will never stop growing.
i will keep the car until i finish studying and then buy stg else.
i will keep the car until i finish studying and then buy stg else.
- :
- 2016 GT ST 47A
Congrats!!! Now you have more mod $$$$$ (evil)
boostedprotege
Member
- :
- 2003 mazda protege dx/2003 mazda protege5
haha naw i needa start buildin up my bank acct while i'm still young lmao... i got plans for the p5 tho nothin like my sedan but jist somethin clean and semi quick lol but thanx i'm stocked to not have ANY car payments.. n beggining of next year i will be lookin for a ms6
boostedprotege
Member
- :
- 2003 mazda protege dx/2003 mazda protege5
Rockin03mp5
Member
- :
- '13 Mazda3 / '13 Edge / Your Mom
Seriously, seriously thinking of taking off the Ronals and picking up the Mazdaspeed AMG's...they definitely need some work, but look sooo sick...
16x7 with a +50 offset...12.2lbs each...
man, where do you find this stuff? and how much. those look neat. the ms-02's look a little too big. you would be hellastupid to get those.
sorry, I have a question, my car is AT type, may I change the AT system to SPORT AT control system, thank u for everybody answer me, thanks again.
change Sport AT as this:
lol... that is my car! go domo!
Finished stripping one of my wheels with air craft stripper... worked great.It left me an awesome surprise underneath.!!!Good things to come.
might be a dumb question but did you remove your tires before stripping your wheels down? i have to repaint mine and dont know how i should go about it.
justanothermp5
Banned
- :
- Rust Bucket
dont use painters tape, that s*** will just absorb the paint stripper, duct tape should work lol
and today i attempted to get the ******* oil pressure gauge working, but it doesnt want to work for me, it lights up, but stays pinned on full pressure, site says bad ground, but i used the same ground as all the other gauges and they work...
oh well...not like i used it before anyways lol
started looking into my new turbo setup now that i got a t3 manifold on the way, its gonna be siicckkk
and today i attempted to get the ******* oil pressure gauge working, but it doesnt want to work for me, it lights up, but stays pinned on full pressure, site says bad ground, but i used the same ground as all the other gauges and they work...
oh well...not like i used it before anyways lol
started looking into my new turbo setup now that i got a t3 manifold on the way, its gonna be siicckkk
fishdonotbounce
Registered Zombie
- :
- 08.5 CWP Speed3
Just bought new HID bulbs. New temperature, new look 
dont use painters tape, that s*** will just absorb the paint stripper, duct tape should work lol
and today i attempted to get the ******* oil pressure gauge working, but it doesnt want to work for me, it lights up, but stays pinned on full pressure, site says bad ground, but i used the same ground as all the other gauges and they work...
oh well...not like i used it before anyways lol
started looking into my new turbo setup now that i got a t3 manifold on the way, its gonna be siicckkk
Did you check the ground at the sensor?
sexy
justanothermp5
Banned
- :
- Rust Bucket
yup, i redid the ground twice now and no difference, i even took the line off and soldered it together to make sure the connection was good
Does anyone know if this works with the protege?
http://www.mazdas247.com/forum/showthread.php?t=123782975
http://www.mazdas247.com/forum/showthread.php?t=123782975
