shane02pro5
25ish_psi
- :
- New Caney TX
What have you done to your P5 today?
- Thread starter Tg5
- Start date
fishdonotbounce
Registered Zombie
- :
- 08.5 CWP Speed3
Clipped a curb with my rear passenger wheel today pulling out of mickey d's. Small nick on the very edge of the lip, but the sidewall split in half like it was cut. Seems that I hit the very corner of the end of the curb. Riding around with a donut until Friday 
.
.kudakev615
Member
- :
- pro5
gaawwdd i love ebay. only place where you can find deals like that. i even got my ractive header for 20 bones shipped 3 years ago and a carbon front fender for my bike for 45 bux shipped
i buy things for around the house on ebay all the time. i can wait 2-5 days for something to be shipped if im saving 70+% off when the shipping ppl (fedex, ups, usps) are dropping off sometimes 3,4,5 packages aday at your house they start to wonder:/
Last edited:
truuuuuuuuuuuuuuuegaawwdd i love ebay. only place where you can find deals like that. i even got my ractive header for 20 bones shipped 3 years ago and a carbon front fender for my bike for 45 bux shipped
went to put my sts on....and this happened
the bolt that goes through the shifter sheered off with the nut still on it. now i know the bolt has a head on it that should turn. anyone think it can be turned and come out. im hoping cuz its hard to get at from under the car and im hoping to finish it tomorrow. but i dont wanna have that sheer off too.
the bolt that goes through the shifter sheered off with the nut still on it. now i know the bolt has a head on it that should turn. anyone think it can be turned and come out. im hoping cuz its hard to get at from under the car and im hoping to finish it tomorrow. but i dont wanna have that sheer off too.
- :
- MSP 1145
went to put my sts on....and this happened
the bolt that goes through the shifter sheered off with the nut still on it. now i know the bolt has a head on it that should turn. anyone think it can be turned and come out. im hoping cuz its hard to get at from under the car and im hoping to finish it tomorrow. but i dont wanna have that sheer off too.
not sure i'm exactly sure what you're talking about.. but if it's the small bolt that holds the shifter to the linkage, after the nuts off, you can just pull it out.. replace it with a strong bolt of the same size.. shouldn't be an issue!!
- :
- MSP 1145
it's def not threaded in man.. that's what the nut was for. try tapping it out with a hammer.. you can try turning it out..
but it shouldn't have to unscrew.
ScratchNSniff
Undisputed Parts God
- :
- Way to Many
Thanks for the vacuum link...
- :
- -- 03 P5 / 23 CX-5 --
Washed it & drove it a little.....odd
kudakev615
Member
- :
- pro5
just finished washing and drying her. thats after working 12+ hours of working on cars at my job and i still found some time to show my baby some love. still gathering my parts getting ready for some changes
haha where you been? hopefully. if all goes well this summer. i looked at that trubolife setup. s**** crazy! good luck on that. Let me know when your instaling. you getting a bov?
not going to do the bov, prob the forge bpv
kudakev615
Member
- :
- pro5
bpv is your friend on a FI fs
- :
- MSP 1145
sounds good man. good luck.
lol. So much for " I'm done putting money into this car." ??
Snatch that Thumper kit FS right now!!!
