What have you done to your P5 today?

[Hank3]

Sold my P5 today at 140K miles for $3250.

 

[EVADE]

Sold my P5 today at 140K miles for $3250.

I've been debating to the same lol

 

[Jackie chan]

I've been debating to the same lol

Nooooo! And I need a new sticker soon if you're still doing it!

Sent from my SM-G900T using Tapatalk

 

[STudMUffin97]

Don't sell guys, mod!!

Sent From Papa Jays Phone

 

[NaturalFlavored]

I don't think there's much left to mod that evade hasn't done already.
My goal is to try and get the fsze running at full potential. That'd be nice.

 

[STudMUffin97]

Still its sad to see one go

Sent From Papa Jays Phone

 

[JazzySP20]

Installed 12v 5W red incandescent globes in the cluster. A little brighter and more red now.

These are what I used.

 

[dorkidori_s13]

just snagged a set of Advan Super Racing Gen 2s from Japan for my P5 Same wheels I have on my S13 hatch.... though a bit narrower!

 

[SlowturboP5]

Installed remanufactured left rear caliper and $8 pads. Also bled the brakes.

 

[dorkidori_s13]

Nothing super exciting, but my new mid section piping showed up today! Now I can get rid of that rusted out mid pipe that won't seal to the muffler properly! Just need to get a new catalytic converter section so I can have a nice new exhaust system! Thank raptor jesus for cheap ebay catbacks hahahhah

EDIT: New Corksport exhaust hangers just came in!!!

 

[Izimo]

Installed AWR header yesterday

 

[farqyj]

Replaced both rear struts today: Broke one on a speed bump yesterday. Yes, actually broke the hat on top of the strut, and the whole thing came up into the rear seat belt bracket. Drove home (slowly) like that and replaced both. This was an Edmonton car most of its life and lots o rust. Had to buy the 'quick struts' because needed the new top hats, cost me $700 for the pair with a discount! *Would have been $1000 without at Lordco, the only place with them* Then changed to my summers and did some other minor maintenance. Had to CUT the sway bar end link nuts off. That was a chore.

 

[NaturalFlavored]

Mazdaspeed door sills and Progress rear sway bar.
Waiting on Moog endlinks to top it off

 

[dorkidori_s13]

just snagged an MP3 intake manifold for my P5 today! on the hunt for the matching ECU now... and JDM intake cam!

 

[323]

just snagged an MP3 intake manifold for my P5 today! on the hunt for the matching ECU now... and JDM intake cam!

Where is your build thread

 

[dorkidori_s13]

eh, i dont really wanna make one... maybe ill do it one day.

EDIT: OK i cracked and made a built thread...

https://www.mazdas247.com/forum/showthread.php?123859689-My-P5-build-thread

 

[323]

i didnt do it!

 

[dorkidori_s13]

gotta love that brittle sun baked plastic

i pulled mine all off a while back since they were all busted up and cracked as it was. fortunately i have a good condition roof rack on the way eeeeeeeeeeeeeeeee!

 

[Preferio]

I've completed the re-bearing of the bottom end of my P5- pump, bearings, front and rear seals. Three of the four mounts are installed. HVAC blower switch will be installed tonight. Transmission may get mated to the engine, but not sure yet.

I don't think I've ever posted in the P5 forum. At least not about my own cars.

 

[915_P5]

Getting the tein's back tomorrow from overhaul, hopefully on the weekend get them on the mp3 and change out all the rear suspension components for some fresh pieces.