GP Light Weight Protege pulleys

[joeleo1]

Hey Brach, do I just send you the original crank pulley for a v3?

 

[Medieval]

Hey Brach, do I just send you the original crank pulley for a v3?

Yes.

 

[Tzar177]

im guessing theres no durability issuses with the v3 pulley?

 

[joeleo1]

Are right then, I'll send it back to you.(bolt)

 

[carbonkid]

Since I have an uninstalled v1, I will do the same (swap for v3).

Address to send to?

 

[joeleo1]

My v1 crank pulley is in the mail, please send the v3 out whenever it is ready. Thanks Brach.

 

[CitizenPro]

Since I have an uninstalled v1, I will do the same (swap for v3).

Address to send to?

Same here. Address to send my uninstalled V1 Crank to plz...

 

[JCell]

damn, my roommate has this set and it looks awesome, but judging from this id say its probably best not to order

 

[Medieval]

damn, my roommate has this set and it looks awesome, but judging from this id say its probably best not to order

Judging by what?

 

[joeleo1]

Out of curiousity Brach, when may the v3 crank pulley be ready? I'm just trying to plan out when exactly I'm going to be putting the pullies on.

 

[JCell]

Judging by what?

people having problems with these

 

[cougar10agREDUX]

people having problems with these

only problem i had was with the original crank pulley, i still have the original PS pulley installed as i've been to lazy to swap it out with the new one.

I've had the all 4 pulleys in since may, no problems except for the V1 crank pulley which i swapped out with the V2 in early july. and no problems since then, and i drive pretty hard sometimes.

as long you tighten the belts properly there are no problems.

most people don't have the tool to measure belt tension, i don't. but the manual also gives belt deflection specs. check the attachment.

 

[Medieval]

people having problems with these

Those issues have been addressed with new designs for sometime now. No issues anymore. We only had 1 PS pulley fail and a new design was released. Replacements were sent to all to ensure nobody else had a issue.

 

[CitizenPro]

Medieval,

Can you please send me an address to mail my unistalled original v1 crank pulley? I emailed you, but recieved no response.

 

[Medieval]

Medieval,

Can you please send me an address to mail my unistalled original v1 crank pulley? I emailed you, but recieved no response.

PM'd

 

[joeleo1]

Out of curiousity Brach, when may the v3 crank pulley be ready? I'm just trying to plan out when exactly I'm going to be putting the pullies on.

 

[CitizenPro]

Out of curiousity Brach, when may the v3 crank pulley be ready? I'm just trying to plan out when exactly I'm going to be putting the pullies on.

Absolutely. I expect to have the new crank pulleys boxed up and on the shelf in 3 weeks. When that happens I will send you off a replacement.

 

[joeleo1]

Thank you!

 

[zoomin MP3]

Took my MP3 to the track a couple weeks ago and had no problems with the pullies. This time I had the complete set including the v2 crank and v2 PS. I will attest to the power gain as I easily saw a decrease of .3-.5 seconds ET. My mile per hour was higher and compared to times I've had in the past, even being slower out of the hole, I made it up and more by the end of the 1/4.

All durability and fitment issues appear to be taken care of, so no one should have concerns of failure from here on out. Just a little message for those of you waiting for that reason.

 

[JPR-MSP]

^^^ are you serious about the 0.3-.5 off your 1/4 mile time?