Are you getting noise and vibration?
Check this out for more information
http://www.exedy.co.uk/index.php?main_page=troubleshooting_guide
What have you done to your MSP today?
- Thread starter baconbitz
- Start date
Are you getting noise and vibration?
Check this out for more information
http://www.exedy.co.uk/index.php?main_page=troubleshooting_guide
hornsfan10609
Certified Mazda Tech
- :
- 2003.5 Mazdaspeed Protege x2
The FMIC kit I ordered showed up yesterday, I am impressed with the quality of the parts for $140 shipped. Just have to wait for a few reducers for the turbo and my BOV pipe to get here and I can put it all on.
churrosurf
Member
- :
- protege 5
I put my oil pressure sender today FINALY!! for my oil pressure gauge. Is a Auto-meter short sweep electrical gauge. So the question is the pressure? when is in idle goes to 25 or less, when I driving, goes to 75 is that good? my car is burning oil anyways, that's the reason I put this gauge. Thanks to IukekiniProtege for the advice.
SeR_Cyclops
Member
- :
- Mazdaspeed Protege
I have always gotten a little chatter but im getting a loud clunk when i let off the clutch when down shifting. Im thinking it might be a spring bad and its not absorbing the shock. I havnt got a chance to really look at it yet.
- :
- '13 CWP MS3 & '16 Mazda6 GT
Bought some black grill paint to spray a light coat on the intercooler before mounting it this weekend 
SpeedAdiction20
Member
- :
- 2003 MAZDASPEED Protege
hey does anyone know where we can still get grille mesh, like I bought my car with West Wings grille mesh that was PC black, and my brother now is looking for the same kind of thing for his msp, but West Wing's doesn't have it available, was looking around and there really isn't anything there, and I don't want that ricer mesh stuff from autozone, should I just contact West Wings and see if they still have that type of mesh and if they would ship a small piece out to me for the grille? anyone else have any ideas?
- :
- 03.5 YLW MSP
worse case is they tell you no they dont have it in stock...
- :
- '13 CWP MS3 & '16 Mazda6 GT
Im wondering with my "greddy type RS" BOV if I should test it on hard or soft setting when I get everything installed. Any ideas on whats best?
fatti03msp
Contributor
- :
- 03 MSP & 91 RX-7 & 00 1500
hard and work your way to softer till you dont hear any turkey.
- :
- '13 CWP MS3 & '16 Mazda6 GT
thanks 
- :
- 03.5 YLW MSP
you need to adjust it at idle so when you rev it the car wont stumble or stall
did you take one of the springs out?
- :
- '13 CWP MS3 & '16 Mazda6 GT
negative, should I?
- :
- 03.5 YLW MSP
Some people do but I couldn't get mine to act right with one or the other spring left in mine. I get turkey on light throttle
- :
- '13 CWP MS3 & '16 Mazda6 GT
I'll try it how it is for now and go from there.
fatti03msp
Contributor
- :
- 03 MSP & 91 RX-7 & 00 1500
i kept both in on mine, same as stealth..... would get a little bit of turkey here and there but as long as you have the maf after the BOV you wont have problems with stumble you just dont want too soft where your boost will open it up to easy and then you have a big ass vac leak and no boost
- :
- '13 CWP MS3 & '16 Mazda6 GT
Finished this in 10 minutes lol
SeR_Cyclops
Member
- :
- Mazdaspeed Protege
Nvm guys, I was pulling up the hill and the tranny blew. I think my welded LSD s*** the bed. Its funny though because I havnt got on my car in forever, and I dont beat on her anymore.
squire0311
Member
- :
- 2003 mazdaspeed protege #1215
lol welded are just as bad as stock shoulda went mfactory or quaife.
