What have you done to your MSP today?
- Thread starter baconbitz
- Start date
Velocifero
Wham Bam thank you Ma'am
- :
- VRM MS6, Sunlight Silver MSP
The idea behind ss braided brake lines is to prevent the ballooning of the line under extreme braking conditions, and get the juice more efficiently to the wheels, for safer (maximum) stopping power. For daily normal driving they won't do too much except look good, if anybody is peaking around all kinds of tight angles of the car, but under race conditions, they are helpful. At an autox I have seen a rubber line that look like it had a tumor growing off it that was a bad spot in the line where the line was ballooning. That wasn't on one of our cars though. I have seen ss lines on our cars fall apart though, think they were cs but I can't be for sure, it was awhile ago.
Here is a little more info I looked up on them:
Stainless steel brake lines improve pedal feel and reduce the amount of time between applied pedal pressure and actual deceleration by preventing expansion, which stock rubber flex lines allow. This provides a quicker pedal response, and allows the driver to maintain consistent brake pressure and precision brake modulation
- :
- '13 CWP MS3 & '16 Mazda6 GT
I have a set sitting in my garage that i one in a raffle... I flushed my brakes not too long ago so they'll probably sit for a while...
- :
- '13 CWP MS3 & '16 Mazda6 GT
yep, have to angle the intake right...
send them to me i can make them work so they dont have to sit around ;-)
- :
- '13 CWP MS3 & '16 Mazda6 GT
ha! get to welding then 
lol
lolha! get to welding then
i told you i could weld no problem i just need the stuff to do it
Velocifero
Wham Bam thank you Ma'am
- :
- VRM MS6, Sunlight Silver MSP
so you can't weld. You possibly could weld if you had the stuff.
....i thought that is what i said??
- :
- '13 CWP MS3 & '16 Mazda6 GT
group hug?
Velocifero
Wham Bam thank you Ma'am
- :
- VRM MS6, Sunlight Silver MSP
- :
- '13 CWP MS3 & '16 Mazda6 GT
(werd)
If you need a new hot pipe there is a FS thread for a hard hot pipe in the For sale section
http://www.mazdas247.com/forum/showthread.php?t=123685000
thanks, i know, looks so tempting, but i wanna go wit a front mount kit in a month or so, therefore i dont wanna waste money on an aftermarket pipe
I'm gonna give that a shot, along with a ton of electrical tape .. It's been raining for the last three days, and I'm not sure if that's what's triggering the ABS light, or if it's the poor connection since the wires aren't soldered.
Guess I'll find out once the weather dries out, but yep, heat shrink wrap is my friend! It's what I used on my HID kit, and they've been perfect.
talontsi97
Member
- :
- 03.5 MSP ti grey-sold
egt gauge finnally finished and working.
GM syncromesh put in.
Randomly ran 9psi tonight out of no where, its been about 6-7 since i owned the car. Guess the real cool mid 50 degree weather had something to do with it, but there have been other cool nights since i owned the car and it didnt do 9lbs. i wasnt even full throttle.
GM syncromesh put in.
Randomly ran 9psi tonight out of no where, its been about 6-7 since i owned the car. Guess the real cool mid 50 degree weather had something to do with it, but there have been other cool nights since i owned the car and it didnt do 9lbs. i wasnt even full throttle.
