Hwy 9 Fun Run!

I'm too lazy to post these pics, so you'll have to go to this link. It's about "devil night" on 06 December in Austria. I've been to soo many of these lately, I'm tired of getting whipped. Yet, I have another party to go to tonight at a club. The club events last until 0500hrs and are pretty unbelieveable. I'll try to get you some more info as I recover.
http://www.mazda323performance.com/forum/viewtopic.php?t=5842
 
lol, It's the same way in Acapulco. When I went there with my family for vacation when I was 16, I couldn't believe it! The discotheques don't even begin to get going until about 2, and by sun-up it's still in full swing...Chicas everywhere!!
 
4_103.jpg




Google has some strange s***.
 
Officer xxxxx was traveling southbound on highway 9 when he observed a
motorcycle, traveling northbound, weaving from side to side. Upon
passing the bike the officer observed a female passenger seated facing
backwards on the lap of the driver. After making a U turn and persuing
said bike, it pulled of the road and stopped. Approaching the bike the
officer observed the driver zipping his pants and the passenger pulling
down her skirt. After checking the bike registration and drivers
license and observing that neither party appeared to be intoxicated the
officer released the couple with warning to ride safely. The motorcycle,
by the way, was a Harley-Davidson.
 
God damn. This boost gauge is a POS to install. You'd think that for 40 ******* bucks they'd throw in the god damn mounting hardware! As it is, I've been to 3(all 3 in my town) different auto parts stores looking for the bad little fitting that goes from the gauge line to the T fitting that (I had to figure out what size I needed before) I bought.

The guy that was helping me said that he went to a s*** load of part stores looking for the same damn connector. He finally found one at Pep Boys...In LA.

What a ******* joke. I can't believe that I'm about to make my own connector out of Shoe Goo.
 
Last edited:
Sorry for the rant. It just seems like common courtesy to include the hardware with the product your selling...or at least a shopping list of parts/sizes the buyer will need. I've been trying to get this thing installed for over a week, and I'm not any closer than I was...although I AM closer to breaking it with a f-ing hammer.

I guess I'll just have to take it to a mechanic...not because I don't know how to install the damn thing, but because I'm sick of dealing with rude pimply-faced kooks at Kragen/Winchester/Napa.
 
What kind of a connector do you need? Just a vacuum tee?

I have many in my garage I am sure I have one that could fit.
 
Thanks, bro. :)
It's a connector that goes between the nylon tube (I think it's 3/16)from the boost gauge to a 1/8 T fitting. I've been everywhere but no luck.
 
Officer xxxxx was traveling southbound on highway 9 when he observed a
motorcycle, traveling northbound, weaving from side to side. Upon
passing the bike the officer observed a female passenger seated facing
backwards on the lap of the driver. After making a U turn and persuing
said bike, it pulled of the road and stopped. Approaching the bike the
officer observed the driver zipping his pants and the passenger pulling
down her skirt. After checking the bike registration and drivers
license and observing that neither party appeared to be intoxicated the
officer released the couple with warning to ride safely. The motorcycle,
by the way, was a Harley-Davidson
****** hwy9!!!
 
So what you are looking for is a reducer coupling?

The boost gauge has a flexible 3/16" rubber vacuum line on it right?

I'll take a look at the t-fittings that I have. I might have one that is 1/8" on 2 sides and 3/16" on the other. if that tube for your boost gauge has some sort of oddball fitting on the end of it, you could always cut the fitting off and just slide the tube over the vacuum-tee.
 
Back