Wagonbacker9
Member
- :
- 2004 'Hoe
I ended up selling the car instead... so you could basically do whatever you wanted with it.
very true. any sections of strait pipe are in all likelyhood not going to be used.
How To: Ebay FMIC
- Thread starter Wagonbacker9
- Start date
- :
- 1989 RX-7 GXL Blaze Red
Id be happy to send you my left overs for just shipping cost. I'll have to double check but, I have a U, 2 straights and a 45. u'd just need couplers and a bov pipe.
Wagonbacker9
Member
- :
- 2004 'Hoe
thats roughly equal to what I'm offering, except with couplers, and a full FMIC worth of pipe instead of 1/4 of the kit and 2 useless straits. Plus the BOV and mounting pipe.
Last edited:
- :
- 1989 RX-7 GXL Blaze Red
depending on how you run it you'd only need 1 or two more pipes.
- :
- 1989 RX-7 GXL Blaze Red
Oh, id go with wagon if he's got everything you need. For sure
- :
- 1989 RX-7 GXL Blaze Red
Wagon is your setup still that way?
Wagonbacker9
Member
- :
- 2004 'Hoe
I never got around to changing the routing... car has been gone for a few months now, and the FMIC setup is one of the remaining parts in the basement. I believe if you added a couple of 90* couplers to the kit as is, cut a hole in the core support, id a little measuring and cutting, you'd be good to go with improved routing.
- :
- 1989 RX-7 GXL Blaze Red
I trimmed about 6 inches off of my U and an inch or two off of the L. So my U doesnt sit high at all compared to the one in wagon's first pic. I used 3 pipes out of the whole kit minus my quickly made intake with a 90 pipe. Didn't use the CAI holes on either side of the egine bay which means i still have my washer and coolant res in their original spots.
- :
- 1989 RX-7 GXL Blaze Red
+1. What do you mean cut a hole in the core support though?
Wagonbacker9
Member
- :
- 2004 'Hoe
Yeah, If I had to do it over again I'd shorten the U off the turbo also. Only reason I didn't is because I had a 2" hump coupler on there to make the transition. lol
next to the rad, to pass the hot pipe through.
- :
- 1989 RX-7 GXL Blaze Red
ah mine is just a reducer
I used 1 of each pipe on my install. So I still have 1 of each pipe put away. I used 1 U pipe,1 90 degree pipe,1 45 degree pipe,1 75 degree pipe..I doubt u can buy each pipe individually plus couplers,clamps and get a cheaper price then just buying a new kit with everything. Straight pipes are definitely useless on the msp. As long as u have enough couplers,u can make anything work
- :
- 1989 RX-7 GXL Blaze Red
and a saw to cut pipes with. Also, whats the 75* for and where'd you get that one?
Last edited:
Wagonbacker9
Member
- :
- 2004 'Hoe
that looks suspiciously like a saw.
- :
- 1989 RX-7 GXL Blaze Red
nice. a grinder would work too. 
2003.5_MSP
Member
- :
- 2003.5 MSP
well i was planning on getting a cx racing one and using the extra pipe to make a cai
I bought number 13 from top to bottom count but I asked for 2 90 degree couplers with the kit. http://shop.ebay.com/i.html?_trkpar...&_sticky=1&_trksid=p3286.c0.m14&_sop=15&_sc=1
2003.5_MSP
Member
- :
- 2003.5 MSP
so the a4 tt rabbit kit? did you ask for the two 90 degree couplers instead of two straight couplers or added to kit?
this one http://cgi.ebay.com/ebaymotors/CXRacing-2-5-Elbow-Coupler-Piping-Kit-A4-TT-Rabbit-_W0QQcmdZViewItemQQhashZitem20ac44060bQQitemZ140329092619QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories
Bc i was prolly gonna get this kit http://cgi.ebay.com/ebaymotors/UNIVERSAL-2-5-TURBO-INTERCOOLER-W-U-PIPING-PIPES-KIT-K-_W0QQcmdZViewItemQQhashZitem3cb7accf4cQQitemZ260779593548QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories#ht_2434wt_1167
this one http://cgi.ebay.com/ebaymotors/CXRacing-2-5-Elbow-Coupler-Piping-Kit-A4-TT-Rabbit-_W0QQcmdZViewItemQQhashZitem20ac44060bQQitemZ140329092619QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories
Bc i was prolly gonna get this kit http://cgi.ebay.com/ebaymotors/UNIVERSAL-2-5-TURBO-INTERCOOLER-W-U-PIPING-PIPES-KIT-K-_W0QQcmdZViewItemQQhashZitem3cb7accf4cQQitemZ260779593548QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories#ht_2434wt_1167
Last edited:
