Gauging Interest: Plug and Play Harnesses

[Captain KRM P5]

Hey Mazdaspeed6 owners, we've got PnP harnesses available. I was asked a long time ago if I would sell the harnesses seperately and I said no. Well, in the interest of helping you guys out, I'm back on the fence for this one. If there is interest I'll sell the harnesses for the Mazdaspeed6 to those who want them so they can run whatever system they feel like without going to town on thier factory harness. Keep in mind this is only for the Mazdaspeed6 right now. We will have Mazdaspeed3 harnesses soon enough, but not right now.

Post your thoughts here. Price would be $200 to $250 for a harness with all wires and both connections (male and female)

 

[sbspeed]

I'd be down with it for $200

 

[RevLimitLaunch]

for $200 i would definitely be down. especially since it's a lot cheaper then getting the pnp harness for the cpe ems...

 

[Captain KRM P5]

I'll add it to the website later today then

 

[tunersteve]

Got any pics of the PnP harness? I want to see how difficult it is to install by splicing in vs the PnP. I plan on buying the XEDE (or the ProCEDE/Hydra) from you in the future, but I want to see if I'm up to the challenge of wiring it in myself.

 

[Captain KRM P5]

Got any pics of the PnP harness? I want to see how difficult it is to install by splicing in vs the PnP. I plan on buying the XEDE (or the ProCEDE/Hydra) from you in the future, but I want to see if I'm up to the challenge of wiring it in myself.

picture of the harness is here; http://www.mazdas247.com/forum/showthread.php?t=123698818

 

[tunersteve]

picture of the harness is here; http://www.mazdas247.com/forum/showthread.php?t=123698818

Thanks Ken, took a look at it, still undecided. I'm gonna have to go hunting for some XEDE installs before I make the decision. I'm aiming for end of summer since I'll be working quite a bit, so I'll treat myself come August.

 

[sbspeed]

Would it be possible to get wiring instructions for both the standback and the xede?

 

[sbspeed]

^^^ was that a dumb question?

 

[Captain KRM P5]

no it was not, i just do not have a set for either here at present. i believe the standback directions are available on CP-e's website

 

[RevLimitLaunch]

alright, just cuz i have to ask to be sure, this harness just goes perfectly inline of the ==factory harness male connector== and ==factory ecu femal connector== correct? lol, that's what i got out of it but figured it's always nice to be sure. how long will the harness extend as well? thanks

 

[ATE BALLER]

I'd be interested. I've contemplated trying out an emanage ultimate. Supposedly several people have had some luck with them on other di cars. IDK though, the Hydra sounds like it'll be the best way to go in the end.

 

[Captain KRM P5]

alright, just cuz i have to ask to be sure, this harness just goes perfectly inline of the ==factory harness male connector== and ==factory ecu femal connector== correct? lol, that's what i got out of it but figured it's always nice to be sure. how long will the harness extend as well? thanks

the harness is about 10 inches long. it acts exactly as you said, an in-between to the ECU and factory harness.

 

[RevLimitLaunch]

oh friggin sweet! when about is the availability?

 

[superskaterxes]

i bought this harness and the CPE EMS from ken and the install went fine.

 

[RevLimitLaunch]

did you find it a hassle or hard time depicting through the white wire harness at all?

 

[Captain KRM P5]

no, we just take our time and go by pin number. its not that bad

 

[RevLimitLaunch]

yeah i usually try to always go by pin number rather than the color people list to tap into.

 

[RevLimitLaunch]

are they ready to ship if it's ordered right away? ill admit i bought the cpe ems and i bought the pnp harness and it's taking a while it seems to get.

 

[Captain KRM P5]

we have the harnesses on hand ready to ship