DG Motorsports CF A-Pillars

[YayArea420]

Does anyone have these? If so how good do they fit? I bought the autometer single gauge pod and since it isn't the full pillar it is pretty ugly. I only want 1 gauge and this is the one I like the most.

 

[changedman]

How does your single gauge pod fit?

i don't like my full pillar (2) and was looking at the just two gauge holder not the whole A pillar

 

[YayArea420]

How does your single gauge pod fit?

i don't like my full pillar (2) and was looking at the just two gauge holder not the whole A pillar

I don't really like how it fit and the pod is black and the pillar is grey. I got some interior paint to try and make it match but the paint I got ended up being more silver than grey. You can make it fit perfectly for sure but I couldn't get it to fit right because I was impatient and it was getting late.

 

[brealmp3]

also interested in the fitment of these!

 

[b00sted]

i have a single pod on my pillar..and ive grown accustomed to it. only thing that sucks is that i had to drill holes into the oem apillar in order for the single gauge pod to hook up.

 

[Demonic-Speed]

It replaces the entire pillar so fit shouldnot be much of a problem.

 

[YayArea420]

The instructions on the site says that you have to drill a hole in the stock a-pillar to feed the lines through. It also says that you have to clip the C/F one to the stock a pillar. Here is the install instructions.

 

[UnNaturalinc]

I had these in my car for a while... I put them OVER the stock pillar covers. I just used the rubber trim to hold it in place. It was solid and easily/completely removable. They installed in like 10 seconds.

 

[YayArea420]

Thank you!!! Someone finally has a straight answer. How hard is it to drill the hole for the gauge?? Is the CF hard to cut through?

 

[b00sted]

just use a 2.25" drill bit..very easily done

 

[UnNaturalinc]

Well, it'll be a hole saw. I'm sure you can get a fine-toothed one at Home Depot or something

Yours didn't come drilled?

 

[YayArea420]

I haven't ordered it yet, but the site says that is doesn't come pre drilled. It would be great if it is pre drilled. I wanted to know if the fitment was good before I purchased them.

 

[UnNaturalinc]

Fitment was great on the ones I had.

Now that I think about it I recall seeing them not drilled.

 

[daedalus]

just ordered them today, i'll let ya know. I'm using this to replace the stock a-pillar ( i dont have the stock a-pillar) so i hope it fits!

 

[LapisBlueProteg]

they do not replace stock a pillar
they are a cover with 6 small holes that need to be drilled on stock a pillar to attach too!
there quality is excellent! amie and jason are good service people!
no cutting in cf is required!

 

[b00sted]

yea i dont think the cf ones come pre-drilled

 

[FunkyBuddha]

I have the cf A-pillar on the passenger side since I have a dual gauge pod on the drivers' side. Fits good. Over top the stock pillar. Use double sided tape as well.

 

[wicked]

I just prdered a 3 gauge piller from crossoveer,is it a replacment?it's not the carbonfiber.

I needed to get rid of my single,because I needed room for boost,wideband,and oil pres

 

[daedalus]

^^ that will be a replacement.

Now that I found out this goes over the stock piece, it looks like i'm gonna be cutting off the pods on my automemter, sanding it down, and attaching the CF to it. I dont really have another solution unless anyone wants to sell me their stocker...