corksport power exhaust

[lncatch]

Im thinking of getting the corksport power exhaust for my msp. I was just wondering for anyone who has it if its too loud for daily driving. I know it removes both the cats. And is it as good a deal as it sound for 400 bucks. Thanks all.

 

[Hypnotized]

For me I felt it was to loud. All I did was use the stock muffler section and now its perfecto. I say buy it no matter what.

 

[EnjoyMinuteMaid]

it really is loud man, if you wanna buy mine i'd probably sell it too you for a lot less than 389+shipping...pm me if your interested. Plus I live in Durham, don't know how far that is from you...

 

[Fai]

Hey EnjoyMinuteMaid do you live in Durham Ontario?

 

[mdaj]

Not loud for me IMO. Great no matter what..

 

[INGREXCO]

it wasn;t to loud for me. it was too loud for neighbors.

 

[Speedplease]

Quite at idle only loud at wot but a good loud I love mine.

 

[EnjoyMinuteMaid]

Hey EnjoyMinuteMaid do you live in Durham Ontario?

Nope, Durham, NC (USA)

 

[poboxjosh]

Not loud for me IMO. Great no matter what..

Did you have to drill a spot for your o2 sensor?

 

[poboxjosh]

it really is loud man, if you wanna buy mine i'd probably sell it too you for a lot less than 389+shipping...pm me if your interested. Plus I live in Durham, don't know how far that is from you...

Did you have to drill a hole for your o2 sensor

 

[Speedplease]

no what you do is get an MIL eliminator kit or make one yourself. After you install this on your o2 sensor, you need to take off the little heat shield on your down pipe. After this locate the bolt on the right side of your down pipe. its on the right side if you laying under the car with your legs toward the front bumber. take out the bolt/plug and insert the o2 sensor into the down pipe tighten and your done. And just zip tie the o2 wire out of the way of anything.

 

[poboxjosh]

no what you do is get an MIL eliminator kit or make one yourself. After you install this on your o2 sensor, you need to take off the little heat shield on your down pipe. After this locate the bolt on the right side of your down pipe. its on the right side if you laying under the car with your legs toward the front bumber. take out the bolt/plug and insert the o2 sensor into the down pipe tighten and your done. And just zip tie the o2 wire out of the way of anything.

Thanks Glad i didnt drill into my exhaust. Still having a hard time finding where to plug the o2 sensor in. (it has been on my factory exhaust since june) any idea where i should look to find where to plug it in?

 

[Speedplease]

Yes read my post above i tell you where to put your o2 sensor. it goes right in the downpipe. the down pipe is the pipe that comes off of the s pipe. its the pipe you hook the first pipe of the exhaust up to the one you have to use the spring bolts for.

 

[speedcicle]

If i am correct isn't there 2 O2 sensors in the car and upstream and a downstream and if so is there 2 places to put them? Just wondreing because i was thinking of buying the cs exhaust for my car.

 

[Speedplease]

yes there is. the factory set up is the first o2 sensor is before all the cats the second is after the cats. read my post above i tell you where to place the o2 sensor after you remove the stock exhaust.

 

[poboxjosh]

Yes read my post above i tell you where to put your o2 sensor. it goes right in the downpipe. the down pipe is the pipe that comes off of the s pipe. its the pipe you hook the first pipe of the exhaust up to the one you have to use the spring bolts for.

Thank you very much you have been most helpful