shane02pro5
25ish_psi
- :
- New Caney TX
10mm deep socket under the pass footwell
What have you done to your P5 today?
- Thread starter Tg5
- Start date
And gloves. Unless you really like a lot of blood...
MazdaSpeeder
Member
- :
- Protege5 (5-spd)
+100000
marcs_sp20
Member
- :
- 02 Mazda 323 Astina SP20 (P5)
That woulda cost a packet!!!
I installed a pair of lowered pedders (aus brand) springs in the rear as my Apexi items were a little too low for me, I am thinking they are for the 4wd Sport20... Also changed oil & filter, and on Thursday I bought some blue wheel lugs that'll be coming this week
- :
- 2006 Infiniti M
i thought you were talking about your miata for a moment. i was like WTF MINE GETS TO 80 BEFORE THE 3/4 MARK WTF lol
i opened mine up and didnt get cut at all.
then when i did the re-swap yesterday to see if i really did get an mp3 flashed ecu, i got cut since i was in a rush because of the rain. no like boo boos!
marcs_sp20
Member
- :
- 02 Mazda 323 Astina SP20 (P5)
Purchased some 2010 MS3 rims for $400aud!!!
Got the trans-motor-mount replaced yesterday with little trouble, just had to take a bunch of crap out to get to it. Got the metal sleeve off motor-bracket that slips into the passenger-side mount (was stuck on), hope I have all the tools I need (some borrowed from work) to get the rounded nut off of the front mount and start to replace the rear (which I've read is HELL)...
Tire with a gashed sidewall (don't ask, not proud, curb involved) replaced today, hope to have the car back on the road tomorrow afternoon, and I hope this cure's its herky-jerky'ness when you come to a complete stop. Just another 4-6 weeks (end of school semester) and I'll be trying to sell it!
Tire with a gashed sidewall (don't ask, not proud, curb involved) replaced today, hope to have the car back on the road tomorrow afternoon, and I hope this cure's its herky-jerky'ness when you come to a complete stop. Just another 4-6 weeks (end of school semester) and I'll be trying to sell it!
mazdaspeedwagon
Member
Nice progress.
Rockin03mp5
Member
- :
- '13 Mazda3 / '13 Edge / Your Mom
test fit this today.
this was what i took a picture of up close last time.
got it painted finally.
thanks bazooka joe!
waiting to get some sort of protection on the bottom, rubber or something. that way there wont be any paint on paint rubbing going on.
this was what i took a picture of up close last time.
got it painted finally.
thanks bazooka joe!
waiting to get some sort of protection on the bottom, rubber or something. that way there wont be any paint on paint rubbing going on.
You're not lowered yet? (lol2)
Rockin03mp5
Member
- :
- '13 Mazda3 / '13 Edge / Your Mom
probably never will be. (i just plan on putting 20's on it to fill the gap.... j/k)
the bolts to the struts and stuff look like they would have to be cut off!
stupid rust and corrosion.
the bolts to the struts and stuff look like they would have to be cut off!
stupid rust and corrosion.
Rockin03mp5
Member
- :
- '13 Mazda3 / '13 Edge / Your Mom
looks good
installed 15mm spacers the other day. Much better.
Looks nice love that yellow in the light's I thinking of doing that myself one of these days if I find an extra set of p5 light's.
yeah i dont think ill be taking my lights apart again any time soon. good experience though
