suspension

I have H&R lower sport springs on my 2 and have major wear on the inside of my tires, are there any camber kits out there that will fit to correct the negative camber?

I need these washers. For both sides. Mine are stripped from being rusted out, and there is much play in my rear struts because of it. These hold the dampers down. I CANNOT find these anywhere else, and I'm asking people on the forums if they can help me out. When removing them, please...

came off my mp3 have 60K on them. 70$ picked up. if not picked up 70$ plus shipping

hey guys. I'm selling my Tein springs. the drop is 1.6 on regular 3's. i had them on my speed 3 which they looked great on. had them on for about 3,000 miles then i upgraded to coilovers. selling for $150

hi all, well seems like ill be purchasing another pair of rota torques this time 18x8 +48 for the MS3. looking to put some super beefy nexen N series tires on them, rolling the fenders won't be an issue if it comes to that. which size would best fill the wheel well? P.S. the car IS NOT...

Hey, I wana drop my 2.0 Es Protege but don't want to buy new springs. So I'm looking on Kijiji and only seem to be Mazda 3 and 6 lowering springs on here, dose anyone know if they would fit onto my Protege Thanks :)

I'm looking to replace the suspension on my 2002 Protege5, but I'm not sure what to buy. I was wonder maybe if Focus SVT suspension would work? That'd be fun...

So i have a 2005 mazda 3 hatch, and my stock struts are pretty much shot. Also I'm really into car audio and have a sound system that weighs about 280ish pounds in total, so the rear suspension is carrying A LOT of weight constantly. So I've been looking into getting coil-overs, but not trying...

Hey I had a oil change recently done on my car and they listed two things, that there's a coolant leak from my thermostat and that the outer tie rod boot is busted.. I saw that these aren't very expensive and was wondering if anyone has advice as to how to change them? I have heard some noise...

oki need help for the slammed life thread. the distance the middle of the fender to the ground front and rear for all mazdas. if anyone has a stock suspension and tire mazda please post those specs it would be an amazing help thank you in advance!!

With the death of The Slammed Thread (RIP), I thought I'd start another one up and hope for the best. :) Rules: 1) If your car is low, post up. 2) If you are working on getting low, post up. 3) Post your specs as well so others know how you did it. 4) No Hating, Trolling, Instigating Drama...

Good morning to all. I'm looking to purchase MSP or P5 front Struts mounts for my P5. I already have the MSP struts, but the original strut mount bearing is seized. If you are selling a complete MSP strut with mount I would be interested as well. I',m located in San Diego, CA. Prefer local...

oops, posted this in the general forum when it should be here Hi Mazda Friends, Took our 5 to the shop at around 50,000 miles and had basically the entire suspension replaced. (New shocks, struts , bushings and sway bar links). The guys at my shop were saying that 50,000 miles was too soon for...

WTB: MS3 / MS5 preferably: Mazdaspeed/ After Market Springs (0.5" drop) and Adjustable rear camber arms and Koni FSD 2100-4045 Anybody got a good used set they are looking to get rid of? Thanks, Brad

WTB: Protege5 Air Suspension. if its out there, i would like to see it. HIT ME UP

OK so i bought my P5 about 2 months ago and I noticed this issue. I'm just getting around to figuring out what's wrong. at first look it seems like my drivers side is really low. the distance between the tire and fender on the drivers side is about 1" and almost 3.5' on the passenger side. so...

Hey Guys, I'm selling my 2011 Mazda 2 Blistein Coilovers. I had them installed for only a week. The wife didn't like the firm ride, so off they came. I'm going to have a friend post them on eBay around 11/15/11. I'm looking for $500 plus shipping (I live in southern California). Cheers, Richard

I know that there aren't any companies out there that produce/manufacture Camber/Caster plates for for & rear applications for 99-03 Mazda Protege's. AWR has produced quality ones in the past, and if enough members can show interest in them, they'll make some batches. We're(KHPRO5) looking to...

Want to buy. I actually NEED to buy some rear camber plates. I've looked and looked. I really can't find any. I don't care what brand, I've heard cusco's are good. I'm looking for preferrably a slightly used set(if no deep scratches). My stock dampeners are going out in the rear, and I...

jut browsing through a car blog and saw this. thought I'd share. http://www.more-japan.com/blogs/