engine

Hello, First of all I would like to thank everyone in advance who would take the time to read the long problem description and try to help at least by giving their opinions. Here is my problem: My friend has a Mazda Premacy 2004 with 1.9 gasoline engine. It is a manual gearbox car. The car...

Hey all. So a few months ago, the CEL came on, car wasn't running any differently, no power loss, same mpg, etc. but I had it read at Autozone as I don't have a reader. code came up P2177, system too lean at off-idle, right bank. I waited on getting around to it, but finally did earlier today...

About a week ago I blew my engine going about 60 at 5,500K it sucks because Ive pulled the engine but now I don't know if I want to swap in something else or get another 2.0 FS9. Last engine was stock, I use the car for rally. but now im not sure if I wanna go with another FS9 and do forged...

This car is fully functional, except that the passenger rear strut mount is completely rusted out and it would cost more to repair than the car is worth. 120,000 miles, 5-speed manual, silver body, 1.6l engine, grey clothe/plastic interior. The Good: Zero problems with the drive train, oil...

SOLD - NOW I NEED TO FIGURE OUT HOW TO REMOVE THIS POST. any help would be appreciated.... MAZDA OEM 99-03 Protege-Engine Torque Strut Mount BJ0N3906YE It is OEM (not "like" OEM) and still bagged/sealed in original bag with Mazda part label on. This is the side mount (# 3) that you can...

Hello, I was driving my 2011 mazda cx 7 before I got home. I tried to turn it on an hour later and it won't start and there is no noise when I turn the key. It is not the battery. The lights turn on and the dashboard symbols as well. But again, I turn the key and there is nothing but silence.

I've got some different advice but I'm trying to piece it together on how i want to connect this egr line to my aftermarket headers that dont line up. Its obviously going to be a custom job but i would like to have a few pics to see what others did and how it worked out. Trying to get rid of...

Hey everyone, Im needing to fix my car before I head out back to college. Two issues; one engine, one suspension. If you guys can figure it out youre amazing. Engine: burning oil on cold startup. I replaced valve guide seals along with spark plugs and valve cover gasket, the smoke was then not...

Hey everyone, so im going to buy some requirements for my car to pass inspection, and i know i need 10w-30 motor oil. But im not sure if i should get full synthetic, or a non synthetic. i know the difference, but i want the best oil i can find that will give her that "umph", you know? I heard...

Hi all. I'm new to this site and found while researching my Tribute's engine problem. The mechanic told me that my timing belt jumped and caused chaos and my valves hit the head. A friend's father said that is not possible since it is a chain, not a belt. It's a 4cyl, 2.3 liter engine with...

Alright guys, so here's a quick back story. I was coming back home on the freeway right after work going roughly around 80mph when my 03 protege lx (FS) MT non-turbo overheated and turned off on me. Since this happened while the car was still in motion, I attempted to start it again while I...

Unfortunately today while tightening up my exhaust mani bolts I got a little to comfortable with one that felt really loose and just kept torquing it down. This resulted in me completely braking off the bolt head while having the treading of the bolts stuck inside of the block head. As of right...

Hey new the forum i recently just bought my old mazda protege 5 back from the guy i sold it to a few years back and he ran it out of oil and now it sounds like a jackhammer.. I haven't messed with it at all since i got it back i unloaded it off my trailer and parked it in the driveway.. It runs...

Hi, I am getting a intermittent noise on my wifes '06 Mazda 5 Sport, the car develops a noise whilst driving. It sounds like a motor has started running and after a couple of seconds you hear a click as it stops. I am assuming the click is from a relay? the noise seems to be coming from under...

I was going to turbo charge by P5 but never did so I am selling my forged internals. these were never installed and are still in their original packaging as pictured. If you are looking to make power and don't want to worry about your engine, this is the way to go. Crower Rods: the strongest...

I just grenaded my 2002 P5 engine and am looking for a direct replacement. Original engine had 162,000 miles on it. Been driving this since new and def don't want this to be the end of it! If anyone has a long block, let me know what you want for it. Thanks so much! -Justin

So I did a rebuild on my MSP and installed forged rods and pistons as well as had everything resurfaced. Well now I have everything together and the car will not start. So first I checked to make sure all the wires were correct and they were. Then checked the sparkplugs and they all spark. So I...

Hello, Im here because I've had issues with the p2177 code for a while now. let me give you a timeline June 2014 --car stalls at red lights, RPM's act funny at idle code p2177 august 2014 ---- Clean throttle body and the sensors, disconnect battery to reset computer june 2015-- damn p2177 is...

Does anyone know where I can find the 2009 MS# engine torgue specs? Im rebuilding the motor

Has anyone cleaned the engine bay of their CX-5? I have not looked too much into it yet, just an idea. People typically recommend to cover electrical components, I was wondering if anyone had a nice picture/chart that would outline the important parts to protect and avoid water on for the CX-5...