Rotorworks Group Buy - **********.com

[StreetUnit]

oh sorry about that, cullen. I didnt read your post right. HA! My mistake

LOL, I have sparco to answer your question...

 

[chowhoundMSP]

with brackets for the msp?

 

[Dr.Sound]

hey dex, how hard were the SS lines to install?
did u have to drain the brake fluid?
how long did it take?

thanks.

 

[Yellospeed]

Check my post history.. there's one about Axxis's part numbers..

It's just the old RX7 pads..

just finished mine.


Oh and btw, does anyone have a part number for the rear Axis pads? Id like to use those when it comes time for the rears. thanks

 

[Dexter]

hey dex, how hard were the SS lines to install?
did u have to drain the brake fluid?
how long did it take?

thanks.

The lines were easy, except for the fact i had a bleeder screw snap off in the caliper., Yes you have to drain and bleed the brake fluid. It took me about 6 hours, mainly due to the whole screw/caliper incident, and doing it around midnight does not help, there are no stores open to pick up a reverse drill bit, etc.

(stooges)

 

[Dr.Sound]

cool.......thanks

 

[OrngSpd03]

A Group buy on a nice Sirius Ready Head unit would be good....the kenwood in the MSP sucks, or Stainless Brake lines. How about a nice boost guage with electronic sender, A cheep one is almost $200! Those are my ideas for the next buy.(you probably already have boost gauges)

 

[OrngSpd03]

A Group buy on a nice Sirius Ready Head unit would be good....the kenwood in the MSP sucks, or Stainless Brake lines. How about a nice boost guage with electronic sender, A cheep one is almost $200! Those are my ideas for the next buy.(you probably already have boost gauges)

I'd be in on a SMIC if it was a good price

 

[jurgs01]

hey dex, how hard were the SS lines to install?
did u have to drain the brake fluid?
how long did it take?

thanks.

The SS brake lines are easy (except for those damn clips). Get the speedbleeders I have in my sig to save you some time and hassle bleeding the brakes. Get the clutch line and do it at the same time also.

 

[StreetUnit]

I'd be in on a SMIC if it was a good price

What is a good price? Prices are set by the amount of materials, time, labor, and overhead put into making a piece. The SMIC is $595 and Turbohoses has done all the R&D to back this unit up. The amount of time put into this piece was rediculous.

Being a consumer myself, if I am already investing $500 on any SMIC that is on market, I am going to spend the extra $60-90 to get the best SMIC available. It is not worth saving the $60-90 on the $500 SMIC unit that is gonna chince out on my gains.

These are limited SMIC's, first come first serve. You get what you pay for baby, and you won't be disappointed.

 

[StreetUnit]

UPS Tracking info:

TIFFANY N. THOMPSON<O</O
T# K007 088 364 0
<O</O
JON THOMAS
T# K014 839 627 0

ROBERT E OBRINGER
T# K014 839 624 3

Matt Maeser
P/U Ready

Eric Chelf
Shipped to PO Box VIA USPS

 

[OrngSpd03]

What is a good price? Prices are set by the amount of materials, time, labor, and overhead put into making a piece. The SMIC is $595 and Turbohoses has done all the R&D to back this unit up. The amount of time put into this piece was rediculous.

Being a consumer myself, if I am already investing $500 on any SMIC that is on market, I am going to spend the extra $60-90 to get the best SMIC available. It is not worth saving the $60-90 on the $500 SMIC unit that is gonna chince out on my gains.

These are limited SMIC's, first come first serve. You get what you pay for baby, and you won't be disappointed.

I have looked into turbohoses SMIC, along with the hardpipes. I think that is the one im getting. Figured if people go in on a group buy we could get a better price for buying 15-30 units at a time from some places. Anyway, I have no other Ideas for a GB, so ill just sit here drink a beer, wait for my rotors and ponder another GB Idea.
(thinkbeer

 

[OrngSpd03]

UPS Tracking info:

TIFFANY N. THOMPSON<O</O
T# K007 088 364 0
<O</O
JON THOMAS
T# K014 839 627 0

ROBERT E OBRINGER
T# K014 839 624 3

Matt Maeser
P/U Ready

Eric Chelf
Shipped to PO Box VIA USPS

PO Box? didn't I give you my home address? Crap I wonder how thats gonna work?

 

[jurgs01]

PO Box? didn't I give you my home address? Crap I wonder how thats gonna work?

Pink slip will be delivered for you to pick it up. No big deal.

 

[StreetUnit]

Eric is outta control guys...

 

[OrngSpd03]

Ill calm down now.....i had a laps...ill be ok!

 

[chowhoundMSP]

AWWW no estimated delivery date on on the tracking. I guess ill just have to keep watching it till its in PA. Thanks again for arranging this one Cullen!

 

[Dexter]

Ahh crap.. . my rotors are making this loud ass scraping noise after i get off the gas and coast a little bit. i dont know what it could be. bleh.

 

[Dr.Sound]

wow
let us know when u figure it out......sux man.

 

[OrngSpd03]

Got my rotors today

Picked up my rotors from the post office today. I can't wait to get them installed. Just waiting on my Corksport SS brake lines which should be here tomorrow!

The only complaint I have so far is the packaging. The Rotors were all packed in one box seprated by newspaper. They will have to be repainted because the paint was all scratched off from them rubbing on each other. The Axxis pads were plastic wrapped together and put in small generick boxes and all the empty space in the main box was filled with cans of Ensure(old people drink) and a roll of unused trash bags. I think they could have saved some shipping cost using foam or something of that nature. Anybody else get them shipped in this manner? Just a bit dissipointing for how much we paid and the long wait.