kyle's protege5
Member
- :
- 2002 MP5-T
do you really feel a difference with it?tekkie said:
New INTAKE MANIFOLD protegegarage
- Thread starter sweetlou69
- Start date
Notorious_V.I.C
Member
- :
- 2003.5 MSP
WOuld this make the warrenty go away??
and bump....any difference if power have you dynoed it yet??
and bump....any difference if power have you dynoed it yet??
- :
- 2002 BJFW, 2007 BK3P, 1979 SA22C, 2005 BK3P
we are in the process of having several people dyno this part with a wide variety of cars (modded, unmodded, turbo, non turbo, etc)
Notorious_V.I.C
Member
- :
- 2003.5 MSP
How about the warrenty thing? Will it void it?
Notorious_V.I.C
Member
- :
- 2003.5 MSP
Nutari said:
Thanks Nutari! I'll look into this. IF this thing is ordered, it does come with all the parts needed for complete install, even the egr pipe tekki was talking about??Jus wish it was 149 again, i would buy this thing now...
(poke)
Ken has to answer that.Notorious_V.I.C said:
all there is on the protegegarage site is this
Cast Single Runner Intake Manifold $199.00
FREE SHIPPING Gains of 15 whp on stock setup, more with supporting modifications. Make your turbo spool much faster, dramatically increase acceleration and increase pull and midrange to top end power with this simple swap. Comes painted in your choice of color.
Notorious_V.I.C
Member
- :
- 2003.5 MSP
Yep, looking at that right now!! Just have to stop drooling..haha Looks tempting...
- :
- 2002 BJFW, 2007 BK3P, 1979 SA22C, 2005 BK3P
Nutari said:
it does not come with the EGR. we plug the hole with a 1/2 inch threaded cap which is fine to drive on. the only downside is a check engine light for "insufficient egr flow". this does not affect drivability. we will add the EGR pipe as an option on the site very soon.
Notorious_V.I.C
Member
- :
- 2003.5 MSP
Coolness....I'll be on the lookout for that option. How about the GB that was a while ago on the mazda3club for this item. You suppose there will be another GB sometime this month??
- :
- 2002 BJFW, 2007 BK3P, 1979 SA22C, 2005 BK3P
Nutari said:
we might do that as well, but i have a feeling most people are going to opt to buy the egr solution when we start to offer it.
when i say buy, i mean that we make no profit, zero, on the egr tube. the absolute best cost i could negotiate with them was $50 per tube. i priced out tekkie's solution and locally it came within $10 of that.
- :
- 2002 BJFW, 2007 BK3P, 1979 SA22C, 2005 BK3P
that i know of, no
Captain KRM P5 said:
theres a solution for this, you could reroute to the valve cover nipple, and there you have the flow needed or, you could cut the pipe close to the IM, leaving the longest part of it connected to the Exh Mani and then use some kind of heat resistnt pipe to do a bridge between both.
Last edited:
funktownp5
Member
- :
- 02 Mazda P5 Turbo
Nutari said:
There has to be a change in manifold pressure when the egr is opened and
closed, or the ecu will throw a CEL (insufficient flow). I made a plate to block
the egr and i am getting this CEL, what i will problably do is drill some holes
into the plate causing a small vacuum leak so the ECU will be happy.
kyle's protege5
Member
- :
- 2002 MP5-T
This place has a lot of little electronics like that,Nutari said:
Baker Electronics
I believe they also used to make a EGR Sim too. I know I found a place that did.....I found it...
ZZ Performance
the link i had did not work to their site so i did a search on zz performance and searched their site then i found it.
Last edited:
