GI: New S-Pipe & J-pipe (FULL DP)

[MSpeed2397]

Is there an interest for a new full DP? I just found a local fabricator that is more than capable of producing some badass products. Pictures are posted below of some of their pieces. If there is an interest I would have to bring my car down to them for test fitting, so let me know if you're interested by posting in this thread.

 

[MSpeed2397]

Edit: Make that somewhat local (90 min or so drive)

 

[GingerBreadMan]

i'd be interested. how big would it be? 3"

 

[lisevolution]

I would be potentially interested. Depends on design, cost, size etc...

 

[MSpeed2397]

Basically I want to gauge interest here to see if I can't get them to make a few of these for a group buy, or better yet get them into full production. Those pictures are just examples of their work. 3" is the goal though.

 

[lisevolution]

at 3" i'd be interested... again would have to see how they plan on doing it... if it'll be split like the GHL and Ion or straight through like the Corksport...

 

[MSpeed2397]

I might see if they can't do something like the V-Band assembly on the DP pictured above...that way it's basically like a quick-release for your DP. I'm just not sure that there's enough room in the engine bay to allow for it.

 

[GingerBreadMan]

^^^ would be so awesome. the dp right now is such an pain to get off, basically have to take off the mani and turbo jus to do so.

 

[MSpeed2397]

Right, that's what I mean...I hope these guys can come through with a new DP...hopefully it will be on the cheap too.

 

[arlsmazdaspeed]

I'm interested... subbin

 

[miss_steele_msp]

Good idea. If I didnt have the GHL i'd be with it.

 

[nazgul350r]

if its similar in design to GHL (seperated wastegate) then I would have some intrest.

 

[dannyboy17]

Price range? I might be interested.

 

[MSpeed2397]

I have not made these arrangements yet. I am trying to get an interest thread going first so I can show them that there is a demand for these. Also, I would like to hear any suggestions or requests.

 

[orng1]

3" downpipe is a tight fit, I'm just now realizing how tight it is. With my 2.5 dp I'm almost rubbing the A/C compresor. I'm going to make my own and am eliminating the A/C compresor to make the space, I had a leak from when I replaced the clutch and never fixed it so I figured it wasn't to big of a loss.

 

[MSpeed2397]

After looking at the space restriction over the weekend, I think it's safe to say that orng1 is more than correct by saying it's a tight fit. I think if it is made, that we will HAVE to have a separate pipe for the wastegate then down to a 3" mating to the midpipe. I am in correspondence with them right now. Hopefully overall price is less than GHL.

 

[evolv]

subbing to see where this goes

 

[nazgul350r]

After looking at the space restriction over the weekend, I think it's safe to say that orng1 is more than correct by saying it's a tight fit. I think if it is made, that we will HAVE to have a separate pipe for the wastegate then down to a 3" mating to the midpipe. I am in correspondence with them right now. Hopefully overall price is less than GHL.

Works Great for ME

 

[mazdaspeedwerx]

what is it going to made of? stainless or aluminized? will it bolt to the stock location? or would the exhaust have to be cut and a new flange welded on
edit. tell them to hurry up too.

 

[Greensleeper]

VERY VERY VERY Interested! Subbing!