Cars for tuning in SE Michigan

[petec]

We are looking for some specific Mazdas in SE MI.

We already have a MSProtege lined up as well as an NA P5. We are now looking for a pre-03 626 and MX6/Probe.

We will be tuning your car on the dyno. You will get to keep the tune in exchange for use of your car. We do ask that you cover the dyno time which is $100. Its a bargain for a dyno-tuned calibration complete with print-out.

PM me or send an e-mail to injected255@yahoo.com

Thanks,

 

[kyle's protege5]

how about a turboed P5?

 

[petec]

how about a turboed P5?

What year?

 

[CasopoliS]

tune my 03.5 MSP please.....

 

[petec]

tune my 03.5 MSP please.....

Toledo???? You're close. I am sure we can do it within the next 2 week or so if you want...

 

[kyle's protege5]

What year?

02, and where at in SE michigan are you? I'm in NE Indiana

 

[petec]

Detroit area.

 

[CasopoliS]

Well.... I have the Unichip. Can you guys tune that? How else were you planning on tuning it? Thx...

 

[tekkie]

since its called fordchip I am guessing they are redoing the stock ecu, I know there is a guy thats doing it in Toronto already

if I did not have the emanage already I would go down there

 

[kyle's protege5]

Detroit area.

Sweet, my exwife lives there and i go up there a lot to take my kids to see her. Thats only about a 2 1/2 hr drive.

Also, how are you gonna tune them? I have an emanage already, but it could use some better tuning. Idles like s*** right now

Another thing that will probaly suck for me is you will most likely want to do dyno runs correct? I'm screwed then. My tranny slips like a b**** right now, so i'm in the process of tracking down the stuff to convert it to a manual.

 

[CasopoliS]

I gots me 2 cars... might just drop that MSP off for testing for you guys!

 

[petec]

This is not a "piggy back" like the Emanage. Its better... I don't even know whats on the Unichip.

This uses new software to reprogram the stock ECU. No additional hardware required. It reflashes right through the diag port.

 

[CasopoliS]

This is not a "piggy back" like the Emanage. Its better... I don't even know whats on the Unichip.

This uses new software to reprogram the stock ECU. No additional hardware required. It reflashes right through the diag port.

I tried to call you to discuss this further... did you get my PM? I am interested.

Thanks
Jon

 

[petec]

I tried to call you to discuss this further... did you get my PM? I am interested.

Thanks
Jon

Honestly, I have had so much interest that I am now thinking of setting up a dyno day for all of the cars. Let me see what I can come up with.

 

[CasopoliS]

Honestly, I have had so much interest that I am now thinking of setting up a dyno day for all of the cars. Let me see what I can come up with.

Oh ok. I was under the impression that some development and testing would need to be done before you could tune/program/chip/etc the 2003.5 Mazdaspeed ecu. I would be more than happy to come dyno... but I am most interested in tuning my ECU.

How many pulls would you estimate for a good tune? 3?

 

[Spooled]

petec, if you can pull this off there will be a lot of people all over that, including me.

 

[tekkie]

Honestly, I have had so much interest that I am now thinking of setting up a dyno day for all of the cars. Let me see what I can come up with.

if you setup a dyno day can you make it public please I would like to come see and dyno my car against one of these to see the comparison plus meet some of the peeps (thumb)

 

[kyle's protege5]

This is not a "piggy back" like the Emanage. Its better... I don't even know whats on the Unichip.

This uses new software to reprogram the stock ECU. No additional hardware required. It reflashes right through the diag port.

does that mean for cars like mine that originally not turboed, would not need things like voltage clamps, FMU's etc? you can reflash my stock ecu to know what to do with the boost? what about with bigger injectors?
Also i didnt think it was possible to reflash the mazda ecu?

 

[petec]

does that mean for cars like mine that originally not turboed, would not need things like voltage clamps, FMU's etc? you can reflash my stock ecu to know what to do with the boost? what about with bigger injectors?
Also i didnt think it was possible to reflash the mazda ecu?

You are correct... No band-aids like clamps, strap-ons or FMUs. Mustang guys never use those anymore and they change MAFs, injectors, size etc..

Internet myth. The Mazdas can and have been reflashed.

 

[Spooled]

So any word on when this dyno day will take place? I'm anxious to see the results.