home from the dyno, results inside

[kingpinMS3]

246.3hp
283.8tq

dyno dynamics lowboy
http://ca.youtube.com/watch?v=MRCd4aqdQkM

mods:
Cobble SRI
corksport test pipe
ets 3.5" intercooler
SSQ II
TRZ dogbone

 

[Powerslave]

nice! but with your sig you would think more... is it a mustang dyno?

 

[kingpinMS3]

nice! but with your sig you would think more... is it a mustang dyno?

dyno dynamics. from what i understand they're about 17% more conservative than other dynos.

edit: it's also humid as s*** today.

 

[Powerslave]

your in houston? im in the woodlands. how much did you pay and where did you go?

 

[Betelgeuse]

It would've been nice to see a base run on that dyno before the mods. Still good numbers though.

 

[kingpinMS3]

your in houston? im in the woodlands. how much did you pay and where did you go?

engine logics, $75 for 3 pulls. nice people.

 

[Powerslave]

not to bad, ive been wanting to do that but im saving my pennies to get a full dyno tune...

 

[laloosh]

so did u get a a/f ratio and run the dh?

 

[kingpinMS3]

so did u get a a/f ratio and run the dh?

yeah. i've been really lazy since i got home. i'll scan the AF graph later.

 

[evo2ms3]

That's great on a dyno dynamics. Another speed 3 down here dyno'd 206whp stock on one.

 

[jville]

Hope the gauge purchase helped with that dyno, lol. Those seem a lil low but humidity=unhappy numbers.

 

[driver311]

sweet, what kinda boost numbers were you seeing?

 

[kingpinMS3]

sweet, what kinda boost numbers were you seeing?

according to the dyno, 17.5 peak tapered to 11(ish)@6k

 

[Aaron2112]

heheh 283.8 lb-ft on the front tires how often do you smoke em up? Those are some nice numbers man.

 

[chaos4]

I too, would expect better numbers, even on the Dyno Dynamics. My MS3 with ONLY the MS CAI pulled 239hp and 280lb/ft of torque on a Dyno Dynamics.(idhitit)

 

[ericrapp]

Thanks for post KP. I believe we'd all like a/f and whatever data was monitored beyond that. Was the intake temperature after IC measured. Just thinking not being front mount ic maybe shes a little warm. Still very cool post

 

[mrlilguy157]

crazy. its 60 degrees out right now, I just went outside. the car is unreal at the 'warmer' temperatures.

in a perfect world, all dyno's would work the same and be calibrated the same.

 

[ericrapp]

I was just concerned that with a top mount if you are not moving enough air through the intercooler. In this picture a front mount would get plenty of air with that fan. But wouldn't you want the fan forcing air in the " ram air " designed grille with hood closed. Sorry obviously I'm new to intercoolers.

 

[kingpinMS3]

I was just concerned that with a top mount if you are not moving enough air through the intercooler. In this picture a front mount would get plenty of air with that fan. But wouldn't you want the fan forcing air in the " ram air " designed grille with hood closed. Sorry obviously I'm new to intercoolers.

yes, which is what the fan was doing.

i know the dyno dynamics are pretty conservative dynos, and it was humid(93%) and mildly warm which are all contributing factors.

i will, however, continue to use this dyno because it's where my baseline was done. it'd be silly to go to another shop and gain +- 60whp when i add a downpipe and cobble accessport.

edit:
i should note that after every run i felt the intercooler to make sure it wasn't heatsoaking. the intake side of the intercooler was significantly cooler than the turbo side.

 

[kingpinMS3]