2003.5 Custom Fog Light Kit
- Thread starter www.03msp.com
- Start date
- Status
www.03msp.com
Member
- :
- 2004 Acura TL
UPDATE! WOO HOO WOO HOO WOO HOO UPDATE!
Thank you XXXXXX! Despite a small file format snag and splines, polygons, lines, and curves, and another wonderful "favor" from a software vendor, the product was going to be cut about 20 minutes ago, but will be cut and shipped out on Monday!
The final product is complete. Once I get them, I'll paint, install, and picturize it for you guys and will accept orders accordingly.
Regarding "whatever lights/list" within reason. That is fine, but you have to understand that I can not stock everything, but if I can obtain it from any of the retail stores here, then yes, I will do it. Remember, I'm not making money on the lights so there is no markup cost except for shipping weight for the lights I do not carry.
- Brian
Thank you XXXXXX! Despite a small file format snag and splines, polygons, lines, and curves, and another wonderful "favor" from a software vendor, the product was going to be cut about 20 minutes ago, but will be cut and shipped out on Monday!
The final product is complete. Once I get them, I'll paint, install, and picturize it for you guys and will accept orders accordingly.
Regarding "whatever lights/list" within reason. That is fine, but you have to understand that I can not stock everything, but if I can obtain it from any of the retail stores here, then yes, I will do it. Remember, I'm not making money on the lights so there is no markup cost except for shipping weight for the lights I do not carry.
- Brian
Last edited:
www.03msp.com
Member
- :
- 2004 Acura TL
You can not cut "behind the hole" because the lip is attached in the cutout area. Please do a SEARCH - as there are MANY discussions about this.
Yeah, I finally rebelled and said SEARCH!
For $25.00-$50.00 EXTRA I'll customize any light you recommend (within reason) to fit our product onto the car. The only requirement is that the lights are center/side mounted and that the diameter behind the glass face not be greater than 3.75".
Yeah, I finally rebelled and said SEARCH!
For $25.00-$50.00 EXTRA I'll customize any light you recommend (within reason) to fit our product onto the car. The only requirement is that the lights are center/side mounted and that the diameter behind the glass face not be greater than 3.75".
www.03msp.com
Member
- :
- 2004 Acura TL
PIAA 40 is 6.5" and is bottom bolt mount
Hercdriver
Member
- :
- 2003.5 MSP
Hey there folks. First post, just found your site. Just wanted to sound off for my intrest in the fog lights when they're finished.
www.03msp.com
Member
- :
- 2004 Acura TL
Looking googlie eyed at the screen here for hours. I'm trying to modify this .dxf file to accomodate that 4" Pilot, plastic casing Driving light. I just need to increase an inner diamter .25" but what a b**** it is working with these damn file formats.
www.03msp.com
Member
- :
- 2004 Acura TL
I did it! I did it! It's 12:18AM - been working for hours on this s*** (not s***, but you know, this plate).
I have been able to work with my original design in .dxf format and have finalized it. I just sent this over in a document Email to XXXXXX explaining the changes and for them to call me Monday when they receive the file, review it, input it into their Laser Cutter and verify it cut okay.
I can now support 4" diameter front to back "driving" lights. So, we're on again. It's too late to update the web page right now, but this means I can virtually do any 4" diameter front to back. Man, talk about being skinny around the edges, but 4" is the absolute max - I squeezed another 2/8" of an inch and recentered.
All done. Very good.
Take care,
- Brian
I have been able to work with my original design in .dxf format and have finalized it. I just sent this over in a document Email to XXXXXX explaining the changes and for them to call me Monday when they receive the file, review it, input it into their Laser Cutter and verify it cut okay.
I can now support 4" diameter front to back "driving" lights. So, we're on again. It's too late to update the web page right now, but this means I can virtually do any 4" diameter front to back. Man, talk about being skinny around the edges, but 4" is the absolute max - I squeezed another 2/8" of an inch and recentered.
All done. Very good.
Take care,
- Brian
Last edited:
www.03msp.com
Member
- :
- 2004 Acura TL
Good morning!
Though it is Saturday, I still have been working on the products.
I have 200% verified the new .dxf file/design. Furthermore, I had purchased the driving lights and they fit in the new design and fit in the bumper. The laser cut template fills the entire gap, nice and tight.
Surprisingly, my backup fabricator received the new file this morning and laser cut a piece. He understands that he is my backup and my primary business partner is in Michigan. I will have *8* kits available for shipment by end of next week, and will have pictures too.
I have updated our web page to reflect how to order. Though, we do not have an "automated" system as of yet (in the upcoming weeks), we do accept PayPal and the instructions to order the kits are posted.
We should have the www.03msp.com domain up very shortly.
I wanted to thank everyone who has participated in this thread and gave feedback as to the design of these kits. Shortly, we will be humbly incorporated and cranking these things out like crazy.
Until then, for those who are interested, PREORDER your kits NOW: http://www.rtekimports.com/mazda/products.htm.
Again, thanks for the support.
Regards,
Brian (zmzmp5)
Though it is Saturday, I still have been working on the products.
I have 200% verified the new .dxf file/design. Furthermore, I had purchased the driving lights and they fit in the new design and fit in the bumper. The laser cut template fills the entire gap, nice and tight.
Surprisingly, my backup fabricator received the new file this morning and laser cut a piece. He understands that he is my backup and my primary business partner is in Michigan. I will have *8* kits available for shipment by end of next week, and will have pictures too.
I have updated our web page to reflect how to order. Though, we do not have an "automated" system as of yet (in the upcoming weeks), we do accept PayPal and the instructions to order the kits are posted.
We should have the www.03msp.com domain up very shortly.
I wanted to thank everyone who has participated in this thread and gave feedback as to the design of these kits. Shortly, we will be humbly incorporated and cranking these things out like crazy.
Until then, for those who are interested, PREORDER your kits NOW: http://www.rtekimports.com/mazda/products.htm.
Again, thanks for the support.
Regards,
Brian (zmzmp5)
Last edited:
Devilspawn
Member
- :
- blue something
nice...can't wait...
www.03msp.com
Member
- :
- 2004 Acura TL
Pics by end of week.
Last edited:
www.03msp.com
Member
- :
- 2004 Acura TL
Can I get a count how many people want:
Fog Lights
Driving Lights
???
Fog Lights
Driving Lights
???
- Status
