What have you done to your MSP today?

got my hood one step closer to going on,

2.0t03speed did you have any trouble with your xc hood fitting?
 
refilled oil in the msp until my next oil change... which will be next week... had to refill cause i drove about 1200 miles this weekend... Import Alliance/Nashville/Gatlinburg..!! all over Tn!
 
will 02 P5 wheels fit the msp? I may have found a cheap set to use for winter wheels and I am hoping they will fit. They are five lug but I know there is more to wheel fitment than that.
 
mgerst1 said:
will 02 P5 wheels fit the msp? I may have found a cheap set to use for winter wheels and I am hoping they will fit. They are five lug but I know there is more to wheel fitment than that.
Click to expand...

yup..sandspeed is sittin on mine right now
 
Did a small revamp on my audio. Tomorrow I will be installing a set of KS62 Kicker component set up front

DSC_2679.jpg

DSC_2681.jpg

DSC_2680.jpg

DSC_2688.jpg

DSC_2689.jpg

DSC_2691.jpg

DSC_2694.jpg

DSC_2693.jpg
 
boostedmsp said:
Did a small revamp on my audio. Tomorrow I will be installing a set of KS62 Kicker component set up front
DSC_2689.jpg
Click to expand...
how you like that sub? i wanted to upgrade sub but wanted to retain stock look.

also whats the diameters of that extension? inner diameter 8 inch and outer 10? or inner 6 and outer 8? whats the height an inch?
 
Last edited:
gonna replace my belt soon, i have some lightweight pullies, would it be benificial on a basically stock setup to throw those on or just wait till the motor is built up more?
 
thecrash91 said:
how you like that sub? i wanted to upgrade sub but wanted to retain stock look.

also whats the diameters of that extension? inner diameter 8 inch and outer 10? or inner 6 and outer 8? whats the height an inch?
Click to expand...

I love the sub but my stock sub was blown when I bought it so I can't really compare. Judging by the build quality of the kenwood, it was garbage from the get go. I am used to a 10 or a 12 but wanted to save space in the trunk so this was the only option without going fiberglass or a crazy project. Keep in mind, I am not very handy with wood so I just guessed. The I cut it out of 5/8" MDF and just traced the old sub for the outside diameter and an old paint can for the inside diameter. It didn't fit at first but just used a jigsaw to trim off little by little. I have all the tools in the world but can not cut a circle for the life of me.

Here is what I did today, only one door and then it started pouring the rain. I was going to put the removable tweeter in the factory tweeter pod but it is way to big, I would have to remove one of the mounting points for the panel. I don't like the way it looks but you will never see it and it sounds great! Factory speaker was 4 ohm and had the included tweeter and this component set is also running at 4 ohm so I left the factory tweeter in place. I plan on installing a JL 300/4 amp on the doors and a 250.1 on the 8".

Kicker Ks62 Component set
DSC_2727.jpg


Also, replaced my driver side door seal since it was damaged and got on my nerves. My oil dipstick was broken and I replaced that today too!
 
Please log in or register to reply here.

New Posts and Comments

B
  • Question Question
2012 MT Fuel Leak Above Transmission?
Replies
2
Views
97
burlmancer
B
R
    • Like
  • Sticky
What have you done to your Mazda5 today?
194 195 196
Replies
4K
Views
926K
zedebra
zedebra
I
2016~2023 Replacing shark fin antenna - headliner removal?
Replies
0
Views
17
Ivan Drago
I
jadmt
No transmission maintenance interval recommended in owner's manual?
Replies
16
Views
843
Ladd
L
J
Which CX-5 years were they built in Japan?
Replies
4
Views
208
jadmt
jadmt
A
2008 CX-9 AC BLOWING ISSUE
Replies
0
Views
24
Anthony8478
A
View more…

New Threads and Articles

Back