How-To: Heated mirrors (See post 22)
- Thread starter VRMS6
- Start date
Well install was a breeze...Snapped a few pics for those intrested... Mirror wiring was plug n play so if your thinking bout it go for it....
Quick write up for install///
Tools are:
1 phillips screwdriver
2 hooked pick
3 8mm socket/rachet
4 door panel clip removal tooks
Drivers door panel removal
1) Pull tweeter trim panel outwards until its loose. you can leave hanging no need to disconnect from wiring.
[/URL][/IMG]
2) Using hook pick remove cover in door handel pocket
3) Remove screw now visable and store
4) Using hook pick pull back cover over screw behind door pull
5) Remove screw that is now visable and remove trim plate.
6) Unplug door lock switch and lay plate aside
7) Pull cover over puddle light straight out and lay aside
8) Unscrew exposed screw and put aside with outers
Note those are the only screws holding the drivers door panel in place.
9) Now comes the fun part as seen on the diagram below there are 9 clips holding the panel to the door.
carefully pull back on the door panel and release those clips.
10) After they are all released pull door panel straight up
you can now lower door panel down no need to unplug all the connectors as you will only be accessing the screws/plug that were hidden behind the door panel to remove the mirror assy.
[/URL][/IMG]
11) Using the 8mm socket unscrew the 3 screws holding the mirror assy in place.
[/URL][/IMG]
12) Unplug electrical plug for mirror and remove mirror assembly
[/URL][/IMG]
[/URL][/IMG]
13) Get heated mirror assy and reverse instructions to install heated mirror.
Pass side is same except there are 2 screws under door handle trim instead of one as in drivers side......
install was a breeze and taking my time only took 45 minutes.... Now for a icy day to test them out........
Quick write up for install///
Tools are:
1 phillips screwdriver
2 hooked pick
3 8mm socket/rachet
4 door panel clip removal tooks
Drivers door panel removal
1) Pull tweeter trim panel outwards until its loose. you can leave hanging no need to disconnect from wiring.
2) Using hook pick remove cover in door handel pocket
3) Remove screw now visable and store
4) Using hook pick pull back cover over screw behind door pull
5) Remove screw that is now visable and remove trim plate.
6) Unplug door lock switch and lay plate aside
7) Pull cover over puddle light straight out and lay aside
8) Unscrew exposed screw and put aside with outers
Note those are the only screws holding the drivers door panel in place.
9) Now comes the fun part as seen on the diagram below there are 9 clips holding the panel to the door.
carefully pull back on the door panel and release those clips.
10) After they are all released pull door panel straight up
you can now lower door panel down no need to unplug all the connectors as you will only be accessing the screws/plug that were hidden behind the door panel to remove the mirror assy.
11) Using the 8mm socket unscrew the 3 screws holding the mirror assy in place.
12) Unplug electrical plug for mirror and remove mirror assembly
13) Get heated mirror assy and reverse instructions to install heated mirror.
Pass side is same except there are 2 screws under door handle trim instead of one as in drivers side......
install was a breeze and taking my time only took 45 minutes.... Now for a icy day to test them out........
Great write-up, and it seems pretty easy now that you have the diagrams of the door clips and screws.
I turned on my rear defoster just to check today, and put my hand on the mirror - sure enough, it warmed right up.
Has anyone installed the side viewmirrors with the led turn signal and puddle lights? What wiring needs to be done to make the signals work correctly?
I turned on my rear defoster just to check today, and put my hand on the mirror - sure enough, it warmed right up.
Has anyone installed the side viewmirrors with the led turn signal and puddle lights? What wiring needs to be done to make the signals work correctly?
- :
- 2011 Mustang GT
Do you have the part #'s for those of us that might be interested in doing this? I live in MI and I'm seriously considering this mod.
- :
- 2011 Mustang GT
Awesome man, thanks. I think this might be worth it.
its an option for some versions. hence why this is easily possible.
- :
- 2011 Mustang GT
I'm trying to get the part numbers for the Liquid Platinum mirrors. I think this is gonna be my next mod since I'm constantly waking up to fogged up mirrors in the morning.
- :
- 2011 Mustang GT
Just a quick update on these, if you have a Liquid Platinum colored MS6, paint code 30S, the part numbers are:
GP9B-69-120B-06 MIRROR (RT)
GP9B-69-180C-06 MIRROR (LT)
GP9B-69-120B-06 MIRROR (RT)
GP9B-69-180C-06 MIRROR (LT)
- :
- 2011 Mustang GT
The entire mirror assembly.
