Ok ill try and be brief so you dont lose interest.
1. Jacked up the car on Saturday to change Oil and Tranny Fluid.
2. Noticed that the inner boot, drivers side, on the axle had spewed grease all over the underside of the suspension in a radial pattern...no biggy, must be a tear in the boot.
3. Ordered a new boot from Mazda, picked it up yesterday, dropped the car off at my cousins so he could take care of it while i was at work.
4. He removed the axle, brought it to an axle shop and had them replace the boot, simple stuff.
5. Came back to the house, re-installed the axle and changed the oil and tranny fluid while the car was in the air. In went 6qts mobile 1 and 3qts Redline MT-90 GL-4 from SU.
6. Picked up my car last night after work, all is well, came home and went to bed.
7. Wake up this morning and back outta the garage and while turning i notice a "wuh wuh wuh" rotation noise from the front suspension/tranny...ONLY when turning about 90 degrees in either direction.
8. By time i get to work the car is hot and the noise is gone. Shoot back up to my cousins at lunch, car is cold...makes the noise. By time i get there, car is hot...no noise.
9. He jacks it up, checks the 3 bolts he pulled yesterday, all are tight and can not resimulate the noise. Fucki it...fluke.
10. On the way back down, car is hot...no noise...BUT...rolling off in second from a slow down in traffic i hear a clunk....try in first...nothing....again in second...same noise.
11. Six rolls around time to go....mind u...no noise after lunch...now at 6...car is cold...noise again. By time i get home..car is hot...no noise.
12. WTF?? My shifts arent as smooth as everyone says after the MT-90...does my car not like it? Is this why its quiet after its warm? Im stumped and confused.
13. At this point i want to take it to the dealer if in case it IS the tranny...but im scared.
14. I have bc coilovers, hotchkis sways, ms rear camber kit, ms cai, cs mm inserts and twm bushings...i dont want to get harassed over warranty...im lost, the noise doesnt make sense...alot of you use the MT-90...any suggestions or advice welcome.
15. Thanks guys.
1. Jacked up the car on Saturday to change Oil and Tranny Fluid.
2. Noticed that the inner boot, drivers side, on the axle had spewed grease all over the underside of the suspension in a radial pattern...no biggy, must be a tear in the boot.
3. Ordered a new boot from Mazda, picked it up yesterday, dropped the car off at my cousins so he could take care of it while i was at work.
4. He removed the axle, brought it to an axle shop and had them replace the boot, simple stuff.
5. Came back to the house, re-installed the axle and changed the oil and tranny fluid while the car was in the air. In went 6qts mobile 1 and 3qts Redline MT-90 GL-4 from SU.
6. Picked up my car last night after work, all is well, came home and went to bed.
7. Wake up this morning and back outta the garage and while turning i notice a "wuh wuh wuh" rotation noise from the front suspension/tranny...ONLY when turning about 90 degrees in either direction.
8. By time i get to work the car is hot and the noise is gone. Shoot back up to my cousins at lunch, car is cold...makes the noise. By time i get there, car is hot...no noise.
9. He jacks it up, checks the 3 bolts he pulled yesterday, all are tight and can not resimulate the noise. Fucki it...fluke.
10. On the way back down, car is hot...no noise...BUT...rolling off in second from a slow down in traffic i hear a clunk....try in first...nothing....again in second...same noise.
11. Six rolls around time to go....mind u...no noise after lunch...now at 6...car is cold...noise again. By time i get home..car is hot...no noise.
12. WTF?? My shifts arent as smooth as everyone says after the MT-90...does my car not like it? Is this why its quiet after its warm? Im stumped and confused.
13. At this point i want to take it to the dealer if in case it IS the tranny...but im scared.
14. I have bc coilovers, hotchkis sways, ms rear camber kit, ms cai, cs mm inserts and twm bushings...i dont want to get harassed over warranty...im lost, the noise doesnt make sense...alot of you use the MT-90...any suggestions or advice welcome.
15. Thanks guys.