shane02pro5
25ish_psi
- :
- New Caney TX
^No doubt... I <3 my J&S
What have you done to your MSP today?
- Thread starter baconbitz
- Start date
Good news! Cars fixed and back on the road! Better news! It wasn't the ecu, it was the wire coming off the coil pack going to cylinder 3, replaced and it's working fine. But I think I still need to order some injector seals cause I've got two leaking I think
95blkprobe
Member
- :
- 95 Blk Probe/ 02 Blk Mica P5
i do have a knocklite if youre looking for one
Washed the car after a 7 hour round trip. Car ran great, averaged 29 mpg. I was bored while letting the car dry, so I snagged a couple pics with a bad camera phone
Washed the car after a 7 hour round trip. Car ran great, averaged 29 mpg. I was bored while letting the car dry, so I snagged a couple pics with a bad camera phone
Last edited:
- :
- 2003 Mazdaspeed Protege 1660, 2004 Winning Blue RX8, 2005 Mazda6
I'm scared to start my car... I mean, it's not ready yet, but I'm nervous about the initial start up. Always like that, though. First time I ever disassembled a bike motor, I was convinced it would never run again. LOL Started up first try with no issues. Same way with my Civic build and engine rebuilds on my Jeeps... It's ******' scary man. I don't know why, but it always bothers me.
2.0t03speed
Member
- :
- 08.5 CWP Speed 3
the trick is to when you're cranking it for the first time put the pedal to the floor that way when it starts up it goes straight up to redline and bounces so then you know everything is good lol.
95blkprobe
Member
- :
- 95 Blk Probe/ 02 Blk Mica P5
actually did this with a 327 my dad and i built for a mud truck. it ran for a few seconds, held that b**** wide open for about 5-7 secs then shut it off. If you have oil psi when you start it back up, everything will be straight.
Though I dont recommend this lol
Though I dont recommend this lol
2.0t03speed
Member
- :
- 08.5 CWP Speed 3
hell yes this is what i'm talking about!!!!
2.0t03speed
Member
- :
- 08.5 CWP Speed 3
lol if it is does that mean i'll be getting a drunk dial call later talking about ms3's & 6's.
Did I not tell you that's what it was via txt? Geeze
After seeing that 700whp MS3 I am thinking my money would be better spent on the MS6, lol. 600awhp sounds like a nice goal!
Well... Yes... But we pulled it all out and rested the spark plug on the motor and it was getting spark so we figured it was fine, but come to find out it was sparking out the side of the boot on the plug, couldn't see it in the sun I guess lol but it's all fixed and ready for this weekend. You Going to cars and coffee before you go to streetwise?
2.0t03speed
Member
- :
- 08.5 CWP Speed 3
take the bumper off
Fairly easy to do? Should I just follow the directions off the manual?
- :
- 1989 RX-7 GXL Blaze Red
just pull really hard right around the fender area on each side, should come off easy then
Seriously? Haha
bikingpro5
Member
- :
- 03 Protege5
like Ryan said..
http://www.mazdas247.com/forum/showthread.php?123782943-How-To-Bumper-Removal-for-Protege5-w-pics!!!
few simple bolts after to remove the light..
- :
- 1989 RX-7 GXL Blaze Red
if it doesnt come of right away use a big hammer to break it loose
