What have you done to your P5 today?
- Thread starter Tg5
- Start date
ProjectBlack
Member
- :
- 2003 Mazda Protege 5
I'd say all around good day for several P5's!
95blkprobe
Member
- :
- 95 Blk Probe/ 02 Blk Mica P5
did my 200 mile break in oil change and put another 130 miles on it today.
ProjectBlack
Member
- :
- 2003 Mazda Protege 5
^ nice!
Rolled the fender's turned out great not bad for ten buck's..
Baseball Bat? Never seen that before, but it makes sense and it's SO practical!
Sticker bomb in the future? Lol. Did rear brakes yesterday, drove around for a while. Doing fronts next week and having a buddy do my lines later. Also got demolish drunk by 4 pm, sobered up and drove the hell out if the car with hard handbraking to really make sure the new rotors/pads mated well.
And a high potential of ******* stuff up too. Yes it works, but man... you really have to be careful with that method.
Lol thanks but I'm not stickerbombing it..personally don't like that soo muc. But I'm going to put them on the rear window ..at least as many as I can while keeping them looking clean.
And haha nice way to mate the brakes. I did that yesterday . I took it around a neighborhoood killin the ebrake.
And haha nice way to mate the brakes. I did that yesterday . I took it around a neighborhoood killin the ebrake.
ProjectBlack
Member
- :
- 2003 Mazda Protege 5
Fog light mod...
roy obanion
Member
- :
- 02 p5, 95 miata
does not compute.
bikingpro5
Member
- :
- 03 Protege5
Last edited:
justanothermp5
Banned
- :
- Rust Bucket
you know ripping the e brake actually doesnt help the pads bed in right?
you want to gradually slow down, speed up to about 40, slowly press the brakes until you slow down to around 5 mph and repeat x10
ripping the s*** out of your ebrake heats up the pads way to fast, and is a pretty quick way to glaze them
you want to gradually slow down, speed up to about 40, slowly press the brakes until you slow down to around 5 mph and repeat x10
ripping the s*** out of your ebrake heats up the pads way to fast, and is a pretty quick way to glaze them
goodfornothing
Member
- :
- 03 22v P5-T
Projecblack, do you have HID's in your fogs?
Good info on bedding the breaks, I changed my pads a month ago.
So I installed my turbo this weekend, took some time because of small predicaments, but it's all in. I have an oil leak to take care of at the oil return fitting on the turbo and a small coolant leak on the feed to the turbo. I installed the MSP ECU with SSAFC wired up and while boosting, right at 4.5k-5k the car bucks/hesitates a little, then speeds up, and hesitates again at 6k. So in other words it's not a smooth powerband. I'm guessing I have a boost leak?
Good info on bedding the breaks, I changed my pads a month ago.
So I installed my turbo this weekend, took some time because of small predicaments, but it's all in. I have an oil leak to take care of at the oil return fitting on the turbo and a small coolant leak on the feed to the turbo. I installed the MSP ECU with SSAFC wired up and while boosting, right at 4.5k-5k the car bucks/hesitates a little, then speeds up, and hesitates again at 6k. So in other words it's not a smooth powerband. I'm guessing I have a boost leak?
ProjectBlack
Member
- :
- 2003 Mazda Protege 5
Nah...just a camera phone pic. They are new fogs though, I just replaced the full fixtures, bulbs, lenses, etc. They're pretty bright.
roy obanion
Member
- :
- 02 p5, 95 miata
put in my fuelly and saw I have been getting 29ish mpg...i am rather happy with that
Work's great fender's turned out really nice you have to be a dumbass to mess them up or be going really fast..If your scared to do it just dont...
