all are very fine choices that I highly suggest
as for what I did to my P5 today, I drove it around but I ordered some new rubber for it!!!
MMMMM shexy!! (idhitit) (drive) can't wait to get these bald nitto's off of her
What have you done to your P5 today?
- Thread starter Tg5
- Start date
all are very fine choices that I highly suggest
as for what I did to my P5 today, I drove it around but I ordered some new rubber for it!!!
MMMMM shexy!! (idhitit) (drive) can't wait to get these bald nitto's off of her
- :
- 03.5 YLW MSP
That shouldn't be to hard to fix!
Just move on man! There are other threads out there... lmao.
- :
- 03.5 YLW MSP
look whos talking at least i had a p5 unlike someone..... lol I wounder who I'm referring to....(uhm)
will do! and if they're anything like what I've heard/seen they should be nothing short of spectacular. Especially for an $85 tire..
Hit the nail right on the head! I'm planning on running these although I have to save a decent amount of money and I plan on finishing the remaining bolt-ons to the engine (manifolds, FMIC, downpipe, exhaust). As for tires I'm actually going to go with some Hankook Ventus RS-2s. I hd considered the RT-615s but they aren't the fantastic tire they once were (there are others out there that are better now). Funny thing, I'm going to go with 18x7.5 wheels and 215/35R18 tires because it's actually lighter than the 17x7.5 and 215/40R17 setup with the same tire!
fishdonotbounce
Registered Zombie
- :
- 08.5 CWP Speed3
Quick question. When you guys replaced your front motor mount, from where did you access that bolt? underneath or above? It may just be my auto tranny but I can't easily access the bolt from any which way.
justanothermp5
Banned
- :
- Rust Bucket
get it on a lift and get underneath with a breaker bar, that would be the easiest way
i couldnt get mine out at all either on jack stands or through the engine bay
so im guessing a lift will be the only thing left lol
i just go to the local hobby shop on base, they let people use lifts and there air tools for 5 bucks an hour
i couldnt get mine out at all either on jack stands or through the engine bay
so im guessing a lift will be the only thing left lol
i just go to the local hobby shop on base, they let people use lifts and there air tools for 5 bucks an hour
shane02pro5
25ish_psi
- :
- New Caney TX
Breaker bar from underneath.
01ProtegeMP3
Member
- :
- 2001 Protege MP3
i know this is a p5 thread but i have a clunk after installing my axr clunk fix... could it be this??
heres my thread
http://www.mazdas247.com/forum/showthread.php?p=4011892#post4011892
How bout neither of you leave and stay to help zee ones wif questions!(boobs)
Rockin03mp5
Member
- :
- '13 Mazda3 / '13 Edge / Your Mom
First of all.
Drove it for the first time in 2 weeks. Was gone for a while. Started right up with a little high rev vroom as if to say she is ready.
Also 16w FTW.
And fog lights FTW. Just fix that fog. Mine had a hole in it. Just took a day to fix with lots of glue. Has been working fine for a month now and I always have my fogs on.
Fog light mod FTW.
Nice sig Ty.
Drove it for the first time in 2 weeks. Was gone for a while. Started right up with a little high rev vroom as if to say she is ready.
Also 16w FTW.
And fog lights FTW. Just fix that fog. Mine had a hole in it. Just took a day to fix with lots of glue. Has been working fine for a month now and I always have my fogs on.
Fog light mod FTW.
Nice sig Ty.
Last edited:
- :
- '13 CWP MS3 & '16 Mazda6 GT
- :
- '13 CWP MS3 & '16 Mazda6 GT
dont forget your laundry...you left it on the driveway.
bronze ftw!
