- :
- 2003 Yellow Beast
Correction, whitems3MONTREAL....Or just get your punk ass back to seattle
The 30 degree cold with heavy rain misses you and I know you miss that wonderful I-5 driving in the pouring ass rain...
What have you done to your P5 today?
- Thread starter Tg5
- Start date
Correction, whitems3MONTREAL....Or just get your punk ass back to seattle
The 30 degree cold with heavy rain misses you and I know you miss that wonderful I-5 driving in the pouring ass rain...- :
- carbon grey 2005 SP23 sedan
Correction, whitems3MONTREAL....Or just get your punk ass back to seattle
I miss being stuck in I-5 traffic...oh wait, no I don't (scratch) lol
I still miss Seattle anyway (spin)
Dropped off the Wagner header at the machine shop to have the EGR bung cleaned up. Dru (wife) said I couldn't put it on her P5 until the car's warranty expired (it did, in December) and that I couldn't put it on if it was going to throw CEL's every 6 weeks like it did on my car!
This should take care of it. My hope is to put the header and intake on the car this week while she's out of town, then see how long it takes her to notice I've done it!
This should take care of it. My hope is to put the header and intake on the car this week while she's out of town, then see how long it takes her to notice I've done it!
- :
- '13 CWP MS3 & '16 Mazda6 GT
hmmmm a header on a N/A, my guess is that she'll figure it out, immediately...
Dropped off the Wagner header at the machine shop to have the EGR bung cleaned up. Dru (wife) said I couldn't put it on her P5 until the car's warranty expired (it did, in December) and that I couldn't put it on if it was going to throw CEL's every 6 weeks like it did on my car!
This should take care of it. My hope is to put the header and intake on the car this week while she's out of town, then see how long it takes her to notice I've done it!
Just got a call from the shop, they did the work, but also noticed some cracks in the welds by the cat flange.... Damnit! I thought I was one of the few relatively lucky ones. Now I'm going to have to pay for the machining of the EGR tube, and I may not be able to use the header anyway. grrrrrr
- :
- '13 CWP MS3 & '16 Mazda6 GT
ah, so you mean its pretty pointless? nice... lol 
- :
- 2004 Redondo Red Pearl Acura TL
I think the bearings and the wheel hub has gone on my front passanger side Well, I'm wasting my whole day running back and forth to the machine shop, but I guess we'll be good to go after this! I'll be spending about $50 all told.
The welds were cracked at the collector, badly enough to see light through! Here's a quick image of what cracked:
Any more cracking, and the little diamond-shaped bit in the middle might have fallen into the cat.
As for whether or not the header does anything, I thought it did when I had it on the LX, and it's the only one legal for STS. Also, I'm going to be going back to Northern VA, and we have emissions inspections there, so keeping the cats is a good idea. ...and no, it didn't make much noise.
The welds were cracked at the collector, badly enough to see light through! Here's a quick image of what cracked:
Any more cracking, and the little diamond-shaped bit in the middle might have fallen into the cat.
As for whether or not the header does anything, I thought it did when I had it on the LX, and it's the only one legal for STS. Also, I'm going to be going back to Northern VA, and we have emissions inspections there, so keeping the cats is a good idea. ...and no, it didn't make much noise.
Put in new oem front strut bearings. Would have said replaced but there was no strut bearings to replace lol. They were completly non-existing. While doing that i noticed my sls motor mount bracket was cracked all the way through. Ordered the new and improved steel bracket. To bad the shipping cost more than the part itself. And cuz the side mount broke now the front sls mount bushing is coming out. Might have to replace that one too but this time im going with awr. The only good news is now my car doesnt clunk when i turn the wheels and the rear awr mount still looks brand new along with the street^^^^ driver side mount.
Since the forum's auto-grudge-holding software will no longer allow "street" and "unit" to be used together, I propose that people henceforth refer to the unmentionable shop as "Street Eunuch."
It will get by the software, it sounds close enough that we all know what we're talking about (not that we didn't know anyway) and it's sufficiently insulting to make the grudge-holders happy, I hope. If not, I'll get "instigating drama" points for this!
