Wash and wax for winter meet!

Status
Not open for further replies.
nah no snap ring tool needed there i installed mine myslef in less than an hour.. pretty easy the directions that came with it were very easy to follow.. only thing i didnt have is white grease but i picked that up at autozone. with all of us there it should take less then 30 minutes.
 
i got that. well i can get one but id then have to not bring my speed 6 and bring my truck instead..its a ranger..not much too see.
 
We'll have to keep an eye on the weather. Few showers possible for Sat. but Sunday looks clear.
 
thanks alotz guys..i got my shock done and the suspension felt much better,it was a biatch to get the rear shock off the car.The first one took three hours the secon 45 minutes..lol, ok now you can add me to the list also,Mark do you mine i bring a friend from the 6club with me?He suppost to go to the meet last time but he was drunk the nite before(stooges) and over slept,his name is ray,6club name ronin45......
 
ya, if it rains we won't be washin or waxin...we can do some mechanical work in the garage..ben's car
 
or fix my damn leaking front mount pipes..the couplers need to be bigger on the corner where it goes past the intake so im buying 4 new ones..if i have them by saturday we could do that for like 15 minutes..
 
Anyone wanna help me install my stock springs on the MS6 at this meet?

These Megan Springs just aren't cutting it. I went on a road trip with my wife, another couple and a full trunk and everyone got a little motion sick. It was bottoming out all over the place and when it wasn't the spring rate was just nauseating. Putting the stock springs back in will only be temporary...until the RPM springs become available. Next spring I'll install those for a 1" drop (Megans are 2" drop).
 
chuyler1 said:
Anyone wanna help me install my stock springs on the MS6 at this meet?

These Megan Springs just aren't cutting it. I went on a road trip with my wife, another couple and a full trunk and everyone got a little motion sick. It was bottoming out all over the place and when it wasn't the spring rate was just nauseating. Putting the stock springs back in will only be temporary...until the RPM springs become available. Next spring I'll install those for a 1" drop (Megans are 2" drop).
Click to expand...
who's got the spring compressor?
 
Damn you guys got some pretty sweet 'weekend meets.' Good stuff mark & co.
 
I've got one and Oleg has a better one. Should take less than an hour if we've got a impact wrench for the compressors.
 
bazooka joe said:
who's got the spring compressor?
Click to expand...

Is one needed? I remember that last wash and wax meet....Jeffrey pulled his P5 into your garage and their was a NEPOC swarm....about two hours later his car was lower! :)

Weather might play a factor on whether or not I make it up. But if mother nature doesn't cooperate, I could always lend a hand wrenching (or handing someone the right tool) plus I will have a new valve cover and coil packs/plugs to install.
 
sanblaster1 said:
Damn you guys got some pretty sweet 'weekend meets.' Good stuff mark & co.
Click to expand...

Start driving now....we can knock back a few to drown our beloved Cubbies sorrow and then a few more to celebrate the hopes and dreams of next season. (drunk)
 
Status
Not open for further replies.

New Posts and Comments

3
    • Like
MyMazda App will not communicate with car (where applicable)
Replies
6
Views
10K
Tgogthefu
T
A
How to lower engine crank time with Forscan?
Replies
6
Views
198
TheMAN
T
S
New Transmission Costs
Replies
0
Views
68
Spudly
S
2
Is the CX-90 Really that Bad? Owner Feedback?
2 3
Replies
53
Views
32K
Freedom55
F
Zombiebstr
2025 CX-5 Lowering Springs
Replies
1
Views
111
N7turbo
N7turbo
G
    • Like
2018 CX-5 Sunroof drain loose or clogged
Replies
13
Views
2K
ShaneRivera
S
View more…

New Threads and Articles

Back