CityRacer
Christopher
1993 Ford Probe~Mazda 2.0fs+g series trans+suspension+etc
Engine+trans:
Mazda~2.0 FSDE
Wiseco 8.7:1
K1~connecting rods
clevite~bearings
Arp main studs
cometic extra thick head gasket
oil pump relief valve shimmed 6mm
oil pan tapped for turbo return line
Blocked bored to 84mm
rotating assembly balanced and blueprinted
Arp head studs
CorkSport stainless steel valves
Eibach valve springs
Mazda~solid lifter conversion
heavy port and polished head
adjustable cam gears (both intake+exhaust)
fsze intake cam
fsde exhaust cam
obx turbo manifold
arp stainless steel exhaust studs
Precision Turbo~GT30R: .48ar~t+.60ar~c
Tial 38mm wastegate~15lb spring
stainless steel dump and wastegate tubes + vband connection to exhaust
Aluminum intercooler piping + 28x12x3 front mount intercooler
Synapse Synchronic Blow Off Valve~recirculated
Gizmo Electric Boost Controller~tuned up to 28psi+scramble boost mode
Aluminum turbo inlet + wire mesh intake filter
EGR + IAC removed with metal plates installed now
cold idle solenoid + wire mesh intake (closes at 99 degrees water temp~good for about 400rpms)
billet check valve for cold idle solenoid
Aluminum pulley =water+power steering
Protege power steering pump conversion
140amp High output alternator + custom overdrive pulley
unorthodox racing aluminum under drive pulley plus crank sensor magnets
custom crank sensor bracket
twin catch can system vented into the drivers wheel well
WeaponR~engine torque damper: bolted to lower trans and center cross member
AWR rear, pass side, and front engine mounts
rebuilt and braced passenger engine mount to body area (tore the mount from the body, had to get it rebuilt stronger)
Twin walbro pumps = 190 in tank+255 in line
Aeromotive rising rate fuel pressure regulator
RCE 650cc injectors
shureflo 150 pump into m4 nozzle (water injection)
NGK spark plugs
NGK Spark plug wires
MSD high vibration ignition coil
MSD high vibration ignition box
polished caps ~ coolant/washer/brake/power steering
polished fuse box lid cover
RonDavis aluminum radiator + 18psi cap / 180o thermostat
polished aluminum radiator cover plate
stainless steel radiator lines
Accusump 1qt + manual valve + in line check valve
oil cooler + thermostatic bypass + sandwich plate + remote ZR1 oil filter+ filter magnet (half moon style)
aluminum heat shielding on anything non metal around the turbo/manifold
mild steel exhaust + resonator + oval straight through glass packed muffler + rusty tip (trying to be somewhat incognito)
corksport ~ eurathane exhaust hangers
RR-Racing short shifter + poly linkage bushings
Spec 4+ clutch (non sprung full faced disc)
Spec aluminum flywheel
Quaife Limited Slip Differential
PAR straight cut 3rd gear
PAR billet trans case bearing cups
stainless steel clutch line
Noe trans fluid
WS2 (tungsten disulfied) added every oil change
Suspension+Brakes:
Tein SS coilovers with front camber plates
corksport front control arm bushings
AWR front adjustable sway bar attachments
King6Fab custom front cradle with integrated control arm support brackets
Addco rear sway bar
King6Fab rear sway bar attachments for Megan Racing lateral arms
Megan racing rear adjustable lateral arms
Megan racing front strut bar
GT-Spec aluminum trailing arms
GT-Spec Aluminum v-brace
GT-Spec rear sub frame center brace
Aluminum brake booster vacuum canister + check valve
k-sport 8-piston front brakes with 13" floating rotors + race pads
6" front brake ducts
MazdaSpeed Protege rear brakes + EBC Yellow brake pads
k-sport hydraulic hand brake
stainless steel brake lines all four corners
ARP wheel studs
redesigned & replaced rear brake hard lines
welded 1"x2" unibody bracing
welded 1"x2" rear strut housing brace
Exterior:
Aerogear ~ Evo front bumper (modified+molded in turn signals)
Aerogear ~ millenium rear bumper (molded)
Aerogear ~ shogun side skirts (molded)
aluminum tail light center filler (molded)
custom painted tail lights
CarbonFiber ~ head light covers (1 of 15 made)
CarbonFiber ~ rear hatch (1 of 15 made)
CarbonFiber ~ rear spoiler (1 of a kind)
CarbonFiber ~ front hood ("Chris's Toy"stenciled under side of hood)
CarbonFiber ~ engine cover
CarbonFiber ~ front bumper filler
12v Shark fin antenna
gas hood props
raised hood spacers
stainless hood pins
BMW windshield sprayer pump
windshield spray nozzles relocated to wiper arms
wiper arm pressure spring braces
clear side markers
led bulbs ~ corner, side markers, and tail lights
6" rally driving lights + rock guards + dark tint films
quad H3 projector HID lights+relays+capacitors
front diffuser back to wheel wells + 3 frame mounts (also serves as an impact guard for the front bumper-very strong)
rear diffuser from wheel wells to rear bumper edge + 3 frame mounts &2 bumper mounts
front 3/4" wheel spacers with the adapter studs
Kosei K1TS graphite 14lb 17" wheels
Dunlop ~ StarSpecs & WinterSport 3ds
Led rear license plate back up light (super brite leds)
black front emblem change
limo tinted back + quarter windows
front removable tow hook bolted to drivers frame rail
interior:
black conversion from blue=carpet+panels+dash+head liner+custom rear compartment
Ultra suede over thick foam rear compartment ( all the way to the trunk)
roll bar & strut brace foam padding + black fabric wrap
AutoPower Race rollbar
RCI 5-point passenger harness
TeamTech 8-point (custom) driver~jet pilot harness + integrated lumbar & energy dispensation padding
matte black dash cover (to kill reflection from the dash)
Sparco Road Line pedals (positioned for heal toe)
TenzoR ~ Rally seats
TenzoR ~ Steering wheel
Sparco ~ Steering wheel adapter
PorsheRacing ~ steering quick release
1" aluminum steering wheel spacers (2= 5" total closer to driver for modified drivers positioning)
horn relocated to steering column + aftermarket button
TWM ~ shift nob
Leather shift lever boot
Center console delete
fuel mixture "on the fly" adjustment nob mounted into custom lower center dash panel
kill switches ~ ecu/fan/water injection/master power
led indicator lights ~ accuvolt/water injection/ecu fault/knock system
gauges ~ ammeter/water temp/oil pressure/fuel pressure/wide band o2/fuel level/system voltage/vacuum boost/egts
Sony xplode head unit
Focal front speakers
Infiniti rear speakers
JBL w3v3 sub+box (under 15lbs & easily removable for track days)
RockfordFosgate punch amp
kinetik hc1800 battery
battery to trunk relocation + zero gauge wire & 300amp fuse
full vehicle rewire from bumper to bumper
Jacobs electronics Accuvolt
aluminum+carbonfiber shield for Accuvolt
J&S safeguard + launch control/flat foot shifting/knock&a/f gauge
Cooling mist vericool water injection controller
SDS EM4E fuel and ignition system
Trackmate GPS dataloger system
ChaseCam video system
i-shift programmable led shift lights
fire extinguisher + roll bar quick release mounts
Midland (car to pit) 2 way radio system
2 additional 12v outlets
Accomplishments?
Simply that I still have her. Been in a wheelchair for a year now, and others have had to drive my car for me. She's still mine though, and I keep her in good shape. A dyno vid to show she is real.
dyno
And a friend of mine on a track last summer.
lapping day
*I'm the only one I know of who has shattered a Pauter rod.
lol
TFMMC
Juan
1979 Mazda RX-7 GS
Engine:
-Electronic ignition ('80+)
-NGK plugs and wires
-Header (unknown brand)
-Custom "chopped" air cleaner
-Custom exhaust w/ Magnaflow dual tip muffler
Exterior:
-Restored and painted Almex "keyhole" wheels
-Eibach Pro Kit springs
-KYB shocks
-Side molding shaved
Interior:
-'84 seats and hidden storage bins
-Custom headliner
-Dual 7 flip out touch screen DVD
-Visonik mono amp
-10" Kicker Comp in custom box
-Pioneer TS-G1343R 5"
-Kicker 11KS35 3.5"
-Kicker DS65 6.5"
-Miata(NA) shift knob and cup holder
Funkalicious21
Hung Tran
2002 MP5-T
Engine Mods: (2.0L Msp Motor Swap 87k)
-12 Slim Fans (2)
-440cc WRX Fuel Injectors
-505 Intake Manifold
-Aeromotive FPR
-ARP Exhaust Studs
-ATX to MTX Engine Harness Swap
-ATP Wastegate
-ATP Turbo Coolant Stainless Steel Lines w/ 10-An Fittings
-AWR Front Motor Mount inserts
-AWR Passenger Side Motor Mount inserts
-AWR Rear Motor Mount inserts
-Forge BOV
-Garret GT2860RS-Disco Potatoe
-Injen CAI
-MAM Straight Water Neck
-MAM Turbo Manifold
-Mazdaspeed Protg Oil Cooler
-Mishimoto Aluminum Radiator
-NGK Spark Plugs Wires
-Optima Redtop 35 Battery
-Outlawed Engineering Intake Spacers
-Perrin Fuel Rail
-Popes 3 Down Pipe
-Stainless Steel Oil Line
-Turbo Life FMIC
-Vibrant Silver Vacuum Block
Fuel Management Mods:
-Mazdaspeed Protg ECU
-Split Second Fuel Time Controller
Transmission/Drive train/Shifter Mods: (ATX to MTX Swap)
-Mazdaspeed Protg LSD transmission Swap
-Mazdaspeed Protg Flywheel
-Mazdaspeed Protg Axles
-Mazdaspeed Protg Manual Shift Linkage Swap
-Mazdaspeed Protg Light Weight Flywheel
-TWM Short Shifter
-TWM Shift Link Bushings
Exhaust Mods:
-3" Pope Down Pipe
-Calleyway J Pipe
-Calleyway S Pipe
-Corksport Hangers
-Thermal R&D 3 Exhaust Cat-Back
Brake Mods:
-ABS Added System, MSP Front And Rear Knuckle and sensor added
-Drilled/Slotted Rotors Front
-Drilled/Slotted Rear Rotors
-Front M6 06-07 big brakes
-Mazdaspeed Protg Rear Brake
-SS Brake Lines
Suspension/Handling Mods:
-AAC Rear Link Kit
-AIX Clunk Fix Kit
-AWR Rear MSP Endlinks
-BC Racing Coilovers (BR Series)
-BC Extended Dampening Cables
-Eibach SPC Camber Bolts
-Ebay Rear Sway Bar for MX-6
-KMR Front Tie Bar
-KMR 4 Point Ladder Brace
-KMR Rear V Brace
-Racing Beat 20mm Rear Sway
-Racing Beat Front 24mm sway
Tires/Rim Mods:
-Blox Extended Lugs
-Blox Extended Studs
-BBS RS 17x9 -13 (Front)
-BBS RS 17x11 +12 (rear)
-Falken 502 205/40/17 (2 Inch Stretch)
-H&R 25mm Spacers Rear
-Hub Centric Rings
-Nankang NS-1 195/40/17
-Rs5 Tenzo 17x7 +42
-Tuner Lungs
-XXR 962 17x9 +35 front
-XXR 962 17x9 +10 Rear
Appearance Mods:
Exterior:
-5% Tint Windows
-AAC Front Bumper Bracket Gap Fix Kit
-Alocade Eyelids
-Custom Retro Fitted Headlights Projectors
-DGM Urethane Front Lip
-ForceFed Single Gauge Steering Column Pod
-Fatlace License Plate Frame
-iSport Carbon Fiber Rear Spoiler Extension Lip
-Latitude Rain-X Wipers
-LED License Plate Light Bulbs
-Mazda6 Rear Wiper Swap
-Shorty Atenna
-Tenon HID Headlight Kit 6K
-Tenon HID Fog Light Kit 3k
Engine:
-Air Diversion Plate
-DGM Engine Cover
-DGM Carbon Fiber Oil Cap Cover
-DGM Carbon Fiber Air Ram Hood
-DGM Valve Cover Brackets
-Engine Semi Wire Tuck
-Engine Dress-up Bolt Kit By HKP05
-ForceFed Wrinkled Black Valve Cover
-Stock Red Strut Bar
Interior:
-Autometer Oil Pressure Guage
-Autometer Boost Guage
-Autometer Wideband
-Carbon Fiber Shift Boot
-Dave-B Cluster Rings
-Dual Pod Gauge Cluster
-HKS Turbo Timer
-Mazdaspeed Protg Shift Knob
-Mazdaspeed Protg Gauge Cluster
-Mazdaspeed Protg Pedals (Clutch, Brakes, and Gas)
-Mazdaspeed Protg Floor Mats
-Mazdaspeed Protg Seats Front/Rear
-Nardi Miata 99-05 Steering Wheel
-Protege5 EL Door Sills
-Protege5 Cargo Net
-Sparco Pedal Covers
Audio/Video:
-Inifnity Basslink Sub/Amp
-Infinity Kappa 6x9 Component Speakers
-Infinity Kappa 6.5 Component Speakers
-Rockford Fosgate P400-4
-Rockford Speaker Cables (sub only)
-Rockford Subwoofer Interconnect RCA
Misc:
-Clarion 2-Way Alarm
-Royal Purple
-MOCC Forum Decal
-Redline MT-90 Manual Transmission Fluid
-Team Pro5 Decal
-Wix Oil Filter
Recognition:
3rd Annual Pleasanton Auto Show Best Mazda 2011
Pleasanton Auto Show 2nd Place Best Team 2009 (MOCC)
3rd Annual Pleasanton Auto Show 1st Place Best Team 2011 (MOCC)
#18 Slammed Member
First Hella-Flushed Protg/Protege5
Team Pro5
Bikingpro5
JT
2003 Protege5
Exterior
DGM Rear CF spoiler - custom painted sides, DGM CF Side mirror covers, DGM CF Grill - OEM mesh insert, DGM CF rear valance, Xcelerated OEM CF hood - Custom painted sides, Aero catch hood latches, Shaved rear hatch, Fog Light Deletes, Lightly tinted rear tails, 4300k HIDS, MazdaSpeed axle back exhaust, Rolled fenders, Shaved Protege5 front bumper, S2000 Antenna, Custom S/S midpipe and resonator, Hella super tones, Gorilla Spline Drive Black Lug Nuts, Black painted roof, Custom mixed PPG blue- close to factory 24A but a bit darker and more pearl, Side molding removed,
Mazda6 rear wiper arm
Interior
Custom Blue suede wrapped pieces, Custom Black Micro-Suede headliner, Custom Black Micro-suede A,B pillars,Custom Blue/Black suede wrapped rear cargo cover, custom wrapped Black door inserts, Protege5 S/S door sills, 5% tint rear windows, 5% tint windshield strip, Yudkib*gauge rings- DIY polished, OEM auto-dim rearview mirror w/ compass & temp
Current Stereo
Pioneer Avic F900BT- sat radio,nav, bluetooth, 250GB hard drive, Power inverter, PS2 in glove box, Infinity Kappa Perfect 6.5CS component speakers 2 sets, 100SF of Dynamat extreme, Monster Rca's, Monster 0Ga wire, Monster 4Ga wire, Tsunami billet battery terminals, Big 3 upgraded with Oga, DIY grounding kit installed, Compustar 2-way starter alarm- battery back up, DEI window modules, control up and down of all 4 windows via remote
Handling
K-Sport coilovers, AWR end links front and rear, MazdaSpeed 6 18"rims- Powder coated glossy black, General Exclaim UHP 215/35/18 tires, Mazda6 front caliper upgrade, EBC Green Stuff pads all 4 corners, EBC drilled and slotted rotors all 4 corners, GT Spec front strut bar, GT Spec rear strut bar
GT Spec lower tie bar, GT Spec Ladder brace, Goodridge S/S brake lines
Engine
Polished 626 valve cover, 1.8L coils and plug wires, Polished billet optima battery holder, Red top optima battery, OBX Silicon radiator hoses, OBX header, Vibrant SRI, K&N air filter
New for 2011
MSP front lip, Projector Retrofit, City Lights, AeroCatch Locking hood Latches, Password:JDM AeroCatch Plus Flush Mounting Plates*,12" & 9" slim fans mounted as pushers, Mini wire tuck/ relocate,GT SPEC Trunk cage -blue,Signature Sound Custom Coolant can, powersteering can, and PCV can,
Signature Sound custom ADP, Street Unit Billet motor mounts, Energy Suspension sway bar bushings- greasable front and rear, MazdaSpeed floor mats, Earls AN fitting and black hoses, VICS removed, port and polished Intake Manifold, JDM Familia leather console arm rest, Engine dress up hardware kit, AAC bumper sag fix, Intermitten wiper stock, Relocated battery, GT SPEC Vbrace and panel, GT SPEC Trailing arms, Front splitter, poly bushings for the AWR endlinks
MSP5
Jonathan Hartley
1987 mazda B1600
Engine
Stock 1.6 miata conversion
Transmission
Miata trans with modified b2200 tail housing and shift links
Suspension
Aim 2" drop spindals
Can do specialties upper and lower tublar control arms
front-slam specalties re-6 air bags
rear-slam specilaties re-7 air bags
12" monster c-notch
Suicide doors 4 link kit
SUicide doors bag over bar brackets
Suicide doors under bar gussets
Suicide doors front bag brackets
8 Smc 3/8 valves
1/2 air line
s-10 upper and lower ball joints
a/c compressor converted to air pump
8 gallon air tank
10 switch box
Exterior
4x4 Front fenders
4x4 bumper end caps
chrome grill
chrome bumper
clear corner lights
clear turn signals
shaved gas door and tail gate handle
chrome mirrors
chrome door handles
solid back window
Interior
Tan tweeded door panels,arm rests glove box
and steering wheel
Custom made center console
Airlift dual and singal needle air gauges
Autometer tach
Bucket seats
Wheels
17x7.5 nissan titan wheels
kumho tires
Stereo
Alpine 9873 cd player
polk audio speakers in all 4 corners
kicker L7 8" subwoofer
kicked 450x1 amp
