GI: isport CF rear diffuser project

[ucMP3]

I'm thinking about looking into a rear valence like the one weaksauce rolls... Depending on how much it would run. Personally, I like those a lot more. And these are $$$

 

[Ash-Lyn]

Updated pictures of test piece

For those of you who wanted to see additional pictures of the test piece .... here they are. Some of you are complaining about how "small" this is, but with the muffler where it is and to keep the diffuser symetrical and centered this is all we can do. Like I mentioned earlier, if there is still interest for one that covers the whole width of the car (it would have to be a two piece diffuser) we will tackle that in the future. If you compare prices with similar sized and shaped diffusers, you will find that we are very reasonable. For those of you who sent deposits please confirm the material and anticipated production date. Thanks, Bob and Bryan

First mounting method

Second mounting method

 

[Outlawstar98]

I want it in carbon fiber ofcorse.

And do you know if you are going to do fenders yet?

 

[Ash-Lyn]

Drew will be here shortly to pick up his car and we will discuss the fender issue then (we was going to provide the fenders for the molds). We probably will do them. Will keep you informed.

 

[SeR_Cyclops]

I like it. I think it looks way better from the mounting point that is under the car.

 

[xDJ DUBx]

Any word on the lip spoiler n2ka was gathering interest for??

 

[BadBandar]

Hmm. Looks interesting. Would it be possible to space the fins out more? Looks alittle small to me.

 

[Ash-Lyn]

Drew picked up his vehicle last night and liked what he saw. We are now moving forward with production of the diffuser "as is". For those of you who have given deposits, please notify us thru PM as to your timeframe. We will be making Drew's (SwirlFX), within the next few days. Thanks, Bob and Bryan

 

[ucMP3]

Could something like this be made?

http://www.aerokits.net/cart/index.php?main_page=product_info&cPath=75_204&products_id=3534

 

[Jaysanooch]

Drew picked up his vehicle last night and liked what he saw. We are now moving forward with production of the diffuser "as is". For those of you who have given deposits, please notify us thru PM as to your timeframe. We will be making Drew's (SwirlFX), within the next few days. Thanks, Bob and Bryan

I coughed up the $75 deposit in good faith because I wanted to see something. The problem now is that I don't like what I see and forced to accept it "as is"!?. I thought before it went to production that our feedback and "approval" would be part of deal.

For those who paid the deposit....I wanna know who likes it enough to fork over another $400??

 

[msp03.5]

I coughed up the $75 deposit in good faith because I wanted to see something. The problem now is that I don't like what I see and forced to accept it "as is"!?. I thought before it went to production that our feedback and "approval" would be part of deal.

For those who paid the deposit....I wanna know who likes it enough to fork over another $400??

I have been going back and forth on this. If I am being completely
honest I am not thrilled about the final product and have a feeling I am going to get it, put it on and still feel the same way. I think I was being optimistic in thinking maybe I will change my mind about it once its on. I am still very 50/50 on it and it sucks because I know they put time and effort into it for us. But at the same time that shouldn't make me feel I should buy a product I am not sure I even like?????????????????????????

 

[Outlawstar98]

It wouldent be hard to have 2 more peices connected on both side of this peice that goes to the side of the bumper. Aka, just attatch it to the side and have it go lower, over, then up, like the spliters above. you know what I mean?

 

[Ash-Lyn]

For the third time I want to explain what is fact. Your muffler dictates the size of this diffuser. For the diffuser to look symetrical on the vehicle you must find the centerline of the vehicle, measure over to the muffler, go the same distance the other direction and you have the width. 1. You all saw our cad drawings before any deposits were sent. 2. We kept asking for dimensions, lip profiles and a loaner in the early stage of planning.
3. When Drew finally brought his vehicle out we then could determine the sizing, attachment points, lip profile and clearances. We immediately upon review posted our findings with our initial rough design. You asked for CAD drawings and we provide preliminary drawings for your review. We overwhelmingly recieved a majority of positive feedback. 4. We, on good faith even started the plug and mold mfg. before all the deposits were in. 5. We feel we have met and satisfied the majority of the desires expressed early in this project. For those of you that are now unsatisfied, you do not have to purchase one. We have tried very hard to make you all happy, but I guess that is impossible. Again, for those of you that sent deposits please PM us as to your plans and keep the business part private. Thanks, Bob

 

[Outlawstar98]

Im officially off Splintercell for the night... LOL!

Pm'd

 

[erick pina]

I want CF front lip, anyone!

 

[Outlawstar98]

^JDP makes a lip for the 2003.5, it's sick lookig, I have one.

 

[Dpwhitehead1]

Could something like this be made?

http://www.aerokits.net/cart/index.php?main_page=product_info&cPath=75_204&products_id=3534

i'm in for that. if they do something like it, awesome. if not, it's fine. thanks for at least making us some s***!

 

[erick pina]

^JDP makes a lip for the 2003.5, it's sick lookig, I have one.

who are they?

 

[ucMP3]

who are they?

Forum search. (hump)

 

[MP3Night]

Looks Awesome! What a freaking good time to do a Turbo build when all this sweet cf parts starts popping up for our cars lol