Marketplace

Trying to sell these turbohoses hardpipes with black couplers. I have a hks flange welded on it close to the throttle body. I am upgrading to a fmic so i wanted to get rid of these. they were bought back in May of this year. Asking for $300 shipped but will take best offer.

Joining the military, this car has got to go. 82,000 Miles It has many new parts including timing belt, mass airflow sensor, PCV, and few others. Rebuilt trans from Mazda, with warranty. Perfect Power EMS(not installed, included) The car runs great, just needs to be tuned for maximum performance, but drives great as is. It has 175 PSI compression across. Garrett Turbo INSTALLED REBUILT GT25 Blitz exhaust FMIC Greddy BOV Autometer A/F guage new transmission and clutch from Mazda, with a warranty, I have the paperwork. HIDS Tires are good. Fronts are almost new. Also including a VS racing carbon fiber hood Reposting because I broke the rules =] Fixed.... I just got the car, put some money into it, and I need to sell it...

Everything goes! I Keep the turbo setup and radio along with speakers! Other than that everything else is for sale. Car did have 124k on it and sat in storage for around 2 years. Items sold: All 4 hub assemblys w caliper Rear trailing arms Front kickpanels Front pillars E-brake cable Gauges Center console Radio bezel Front and rear seats are in process Floor mats are in process Prices can be negotiated, Buyer pays shipping, I'm in indianapolis and have paypal ready to go and a lot of boxes.

turbo xs dual stage boost controller 240$ new you pay $75 plus shipping koso digital meter control unit boost gauge (15 psi max) $60 plus shipping awr front motor mount $45 plus shipping factory lsd make me an offer all parts used open to reasonable offers, pm's will work best

ok guys, havent been around in a loonnnngggg time, but here it is. trying to cater to locals first because it will be a b**** to ship most of this stuff. so for shipping, the more you buy, the better the deal. if you want a bunch of small insignificant things then i will just charge you for a "box" and basically whatever i can fit in the box goes. shipping is NOT included and buyer pays paypal charges so the yellow car is going. getting stripped down to the bare minimum and then either sold or scrapped. its a shame with all the work i put into it, but its been sitting here for almost 5 years now doing nothing. its time to go. if there is anything you can think of that you might want just ask. be patient because i will be getting a...

I bought this part from carquest because i thought i had a bad one. turns out it was a loose manifold bolt!! It is BRAND NEW never opened. 20.00 shipped. Please text or call me...[removed]. This will make transactions alot easier for all involved. Will ship intl. Prefer paypal for payment. Thanx for looking. [

300shipped

hey guys.. as you can tell by my screen name, i don't peruse these forums too often.. i finally took this off of my ex's MSP.. did the "kill your turkeys" mod and it worked perfectly.. i am unsure of mileage.. don't know if the BOV still functions properly.. epoxy looks like it needs to be redone.. $60 shipped UPS Ground & paypaled.. thanks for looking..

Just like the title states I got some items for sale that i got from the yard so no i dont realy have a back ground on them so thats why threre cheap as well there is no returns. But ill be hohnest im not trying to sell junk so if i know that if i couldnt restore it or get it restored im not posting it. also shipping will be calculated after you give me your info and i will always try to find you the best deal.. first item i got is fuel injectors on the rail-$30 my msp spoiler has scratches-$50 head off a 2002 lx-$135 lx cams intake exhuast with hardeware-$60

so as i make this thread, i feel pretty bad... but hopefully these parts will go to a new home and you guys will have fun with them... especially all the custom pieces... put them to good use. all parts have been sitting from months to a couple years so need to be cleaned, but as i have a garage full of them, they didnt get cleaned for the pics. ill clean them up before shipping/drop off though most have tracked me through my build thread of me trying to build a monster car (in competition with Miguel, jokes) but sadly ive decided to use the money wrapped up in this to get something new and reliable as ive been in and out of driving my msps for a while now since always seems to come up with them.. i would have LOVED to finish...

Separate, or together...make offer. '86 engine out, interior panels/rugs gone. Was to be converted into race car SCCA. Imaculate body, even waxed engine compartment. 4 bolt wheels, with transmission back. Engine parts in baskets. '89 complete and did run for me the only time I tried. 5 bolt wheels, body rough with one major dent and some Bondo, cracked windshield, drive train complete, exhaust system gone now. Intention was to use the engine and brakes/wheels for above car in race car build. I believe the tub is solid. Pictures available on request. Also have Granny's Speedshop Ford Basic installation kit. Located in 14120. Transportation can be discussed. Bill

I have a few things i need to get rid of to make room in the basment. 1) FS valve cover. great for powdercoating- sold 2) Sub shelf. was going to use this as a template for building something for a 10'' or a 12''- best offer, local pickup prefered as it would cost more than its worth to ship it. no amp or sub included. 3) MSP rear lip. blazing yellow. its dirty and showing some wear but nothing major and no melting. no hardware included as it was lost when i was moving back home from school. again best offer, local pickup prefered as it would cost more than its worth to ship it. SOLD 4) a pillar triple gauge pod. allready attached to a pillar. all you gotta do is drop your gauges in, repaint the pod if you would like, and wire it...

Im selling a few parts from my MSP. I dont have the car anymore I sold it, but I had a few left over parts just sitting in my garage and I figured I would put them up here to see if anyone would want them. All Parts only have 60 k miles on them. Im not sure what these are worth so I am taking offers. If my prices are too high are low that is due to my lack of knowledge on what they are worth. Complete Stock MSP Cylinder Head / Valve Cover / Cams / Valves / Intake / Throttle Body / Fuel Injectors ect...... Complete Set $550 Stock MSP Radiator Hoses $30 Oil Pan & Pick up Tube $40 Coolant lines 20 Stock turbo / Down Pipe / Manifold Complete Set $300 Let me know if your Interested, and Like I said Ill take offers, just...

60-1 5 bolt downpipe, one is broken, new stud can easily be drilled and tapped. Bolts right up to MSP Also needs the wg actuator shaft Minimal shaft play. Bought as a replacement for a bad 60-1 but I put a different turbo on instead. $400 $420 shipped I can txt pics [removed]

I have a full vibrant catback exhaust for 500$ custommsp side mount intercooler for 250$ Hardpipes for SMIC 200$ shipping included on all prices!! www.Photobucket.com/michaelsawdy

Like the title says, I'm looking to trade my INJEN cold air intake for a short ram style. Brand isn't a huge deal to me, just so that it has a nice filter. Untitled by cmezz331, on Flickr Tracking number will be included. You ship first, I can provide feedback from others if desired. Let me know what you have! Thanks! Cory Mods, if the pics aren't right let me know, I forgot what I had to put on the paper.

Here is a brand new set of 16 Muteki Steel Lugs. I am selling the set of 16 (which are brand new) because I had bought these lugs before for my car and two of them got stripped and to replace them I had to buy a new full set. So please remember that THIS SET ONLY CONTAINS 16 LUG NUTS NOT 20. I pulled 4 lugs so that I have 2 extra and so that these can be sold to anyone that has 4 lug set up OR a 5 lug set up with wheel locks. It includes the socket adapter tool. I haven't seen these neo chrome ones online for cheaper than $109 +shipping so I am asking $100 shipped since they are BRAND NEW. The color is hard to tell in my photos, but you can google "sr48 neo" and see... theyre mainly yellow with some dark purple/blue...

I am going to be upgrading to a fmic next week and wanted to sell my hardpipes. They are made by turbohoses with black couplers. It has a HKS flange welded to it. I will get pictures of them once I get my fmic hooked up. I bought these back in may so they are fairly new. I was wanting to get $300 out of them or best offer. This price would include shipping. If anyone is interested start the bid and I will hold them for the highest offer.

I have the original suspension and exhaust from my spicy for sale, these parts were only on the car 6 months before being replaced for better aftermarket equipment. I will also be selling the stock turbo setup along with the factory manifold and the thunder V2 that I am using now, should have my T3 with steedspeed installed soon. pm if interested, only seriuos inquires please!!!

Hello everyone and welcome, I recieved a full engine and trans with my mazda protege. I have never broke it down to much nor have I ever really opened it up. The bottom end supposably needs rings from the previous owner. The bottom end is stock, trans is stock with limited slip. The head has a mild port and a 5 angle valve job from what I was told. The head doesnt have much mileage on it and I dont know how much on the bottom end and trans. I'm looking into it now. So basically I dont need this anymore and its just taking up space in the shed. Let me know if anyone is interested in trading or buying these items. I will ship if buyer pays for shipping. I would like to get rid of as a whole. The head can be used or builtup on the side...