Mazdaspeed2oo35
600whp - 600wtq at 30 PSI
Bro, that's just the model name of it.. you are not going to gain s*** load of HP with just a muffler.. if you combine this muffler with a 3 inch exhaust and mods you'll sure will gain some good Horsepower
Greddy Ti-C vs HKS Hi Power Catback Exhaust
- Thread starter Unkillable2
- Start date
Bro, that's just the model name of it.. you are not going to gain s*** load of HP with just a muffler.. if you combine this muffler with a 3 inch exhaust and mods you'll sure will gain some good Horsepower
Unkillable2
Member
- :
- Mazdaspeed 3 (True Red)
ok ok now i got a really noob question... what is the pipe in between the Catalytic Converters and the muffler call? lol this is probably what Mazdaspeed2oo35 mean but i just want to ask to make sure! would it be a good idea to just go to a muffler shop and get a custom pipe that's in betweeen the Catalytic Converters and the muffler and then weld a hks muffler in the back?
Mazdaspeed2oo35
600whp - 600wtq at 30 PSI
This is how my car looks like in the bottom.. you can see how my exhaust is made.
http://www.cardomain.com/member_pag...s/11/web/2315000-2315999/2315771_179_full.jpg
http://www.cardomain.com/member_pag...s/11/web/2315000-2315999/2315771_339_full.jpg
http://www.cardomain.com/member_pag...s/11/web/2315000-2315999/2315771_337_full.jpg
http://www.cardomain.com/member_pag...15000-2315999/2315771_331_full.jpg?305003-233
Are you talking about the resonators? And if I was you and you like the canister tip, I would just grab the Greddy. Power is all the same and sounds pretty good on youtube.
jam_asian85
Member
- :
- Mazdaspeed 3
Send speedyhans a pm, it's his red speed3, he'll be able to tell you about his set up
Mazdaspeed2oo35
600whp - 600wtq at 30 PSI
All i have to say, his MS3 looks so damn Good bro, with that muffler a little to the side, even carbon HKS looks so good in a red car.. im in love how his ms3 looks from the back.. no doubt HKS makes the nicest Mufflers..
jam_asian85
Member
- :
- Mazdaspeed 3
yup the exhaust looks pretty good, you should see how low the exhaust piping hangs
Mazdaspeed2oo35
600whp - 600wtq at 30 PSI
I would like to see more bigger pictures of his setup... oh wait he did his exhaust under axle ?
jam_asian85
Member
- :
- Mazdaspeed 3
don't quite remember what he said, i'll try and snap some new pics wed
Mazdaspeed2oo35
600whp - 600wtq at 30 PSI
Bro, if i had to decide i think there is no comparison between HKS and Greddy Exhaust wise.. the HKS mufflers are so damn beautiful and good.. all big boys runs them..
- :
- 10 MS3
Here's the MS3 specific HKS CBE:
Greddy:
Greddy:
Last edited:
knowledge007
Banned
Considering I have the CPE TBE with one high flow and 12" muffler, it was just a rhetorical question. We all know that cat backs are worthless alone.
Unkillable2
Member
- :
- Mazdaspeed 3 (True Red)
well i found out that the red speed 3 picture is a custom 3" catback with a Universal Carbon Ti Muffler from hks. that sounds pretty tight. i think that's what i'm going with.
Mazdaspeed2oo35
600whp - 600wtq at 30 PSI
I told you Brotha.. go for it, you can't go wrong with how that HKS looks and sounds..
Unkillable2
Member
- :
- Mazdaspeed 3 (True Red)
yeah man. thx for all you guys help! now i can't wait to get the exhaust...
Unkillable2
Member
- :
- Mazdaspeed 3 (True Red)
custom 3" piping with a Universal Carbon Ti Muffler from hks.
If you're going to buy Greddy, do it now.
http://www.autoblog.com/2008/09/10/japanese-tuning-firm-trust-greddy-declares-bankruptcy
http://www.autoblog.com/2008/09/10/japanese-tuning-firm-trust-greddy-declares-bankruptcy
- :
- 10 MS3
