timing

  1. E

    DFW Mechanic or Speedshop?

    Any body know a good mechanic in DFW or shop that could help me get my MSP running healthy again?
  2. E

    Help! Car backfires and bogs down at 3k *drives rough*

    Hello everyone, I am having some serious issues with my 03'MSP. The car cranks up but shortly after it will shut off. While driving the car itroughly jerks and bogs down at 3k. I didn't see any vacuum hoses off. The car smells like it's running extremely rich. 3-days ago I replaced the timing...
  3. W

    Air coming out intake after rebuild

    I have a 2000 626 2.5L that I have just rebuilt. Original problem was a spun rod bearing which led to the rebuild. I got the motor back in, turn it over, and I have air coming out the intake. I lined up my timing marks like the manual said but is it still possible I am 180 out? The car will not...
  4. P

    Mazdaspeed 3/6 complete vvt replacement kit

    1 L3K9-12-4X0C-9U: Variable Valve Actuator 2 L3K9-12-429: Washers 1 LF01-11-406: Crank Shaft Pulley Lock Bolt 1 9XG0-99-667L: Blind Plug 1 L3K9-12-201A: Timing Chain 1 L3K9-10-230: Valve Cover Gasket 14 LFBL-10-237...
  5. K

    Timing belt

    Hey I now have 166,xxx miles on my car and the ac just went out. Anyways I got it fixed and was wondering what I might need in order to get my timing belt replaced. I know they sell the kits but I was wondering if I necessarily need the whole kit. Also if there are any other seals or o-rings...
  6. B

    timming

    does the msp have a knock sensor with self adjusting timing? If it does then it would make sence to run a water/meth kit to make the car run cooler and make more timming advance and if its self adjusting it will be safe for when u run out of fluid cuz it would just reard timing untill it is...
  7. A

    Timing

    Hey i am new to the forums but not to mechanics, i built my fs-de with fs-ze internals, over bored pistons, j-spec cams, the whole 9 i got 10k+ in the block alone. when i crnak th ecar over it does not start, it motors but wont completly fire over. the crank is TDC so are the cams, now i have...
  8. Y

    EcuTek

    pretty interesting stuff! http://www.ecutek.com/products/proecu/flashcan/mazda_disi/ I sure hope someone tries this out soon. Dont wanna jump off the boat first. Seen a post on the mazda6 forums no results
  9. M

    1.6l 1999 protege timing and starting issues

    waterpump went out. replaced, as well as timing belt. I jus timed the cams and went starte it jumped outa time again. redid checked crank and cams. retimed. won't start. ichecked if the car had a fire and nope. are my coil packs bad? what could be the prob. engine rotates good jus no start...
  10. D

    FS - P5 waterpump/timing belt "kit"

    Sold. I picked up a new waterpump with timing belt and other miscellaneous parts before selling the car. I never got around to putting them on the car obviously. I'd take $80 plus shipping. This is a new pump, not a remanufactured/rebuilt. Might look at other offers.
  11. B

    Camshaft Timing Marks

    2000 Protege ZM 1.6 DOHC I changed the timing belt, and it ran terribly, then not at all. When I removed the plugs, all four were very wet. The cam timing marks were one notch off each. The intake cam was rotated too far clockwise, and the exhaust cam was too far counterclockwise, moving the...
Back