clutch

Hey Everyone, Newly Registered here although I'm been looking over these forums for a while... I have a 2013 Mazda CX 5 manual transmission with 95,000 Miles on it. I just recently replaced the slave cylinder after discovering a leak. However since replacing it my clutch pedal has become...

Anyone replace one of these yet? Seems really early at 75,000 miles. I was reading the service Manuel that I downloaded from this site. The clutch pedal assembly has to be removed with the master cylinder as a single unit. Then I can replace the master cylinder. Ok a lot of work but I can...

How is everyone doing? I just joined and I have a blue P5 that ive had for about 2 years, shes got 205k miles on it and burns about 1.5 qts of oil a week.... I have an engine in putting in in the next few weeks but I was having a hard time finding a clutch for it. So I called Mazda to ask if it...

Hi All, first post: Question: Has anyone removed the Clutch Delay Valve on a current model Mazda 3? Or have ideas how it can be done? I'm VERY keen to give it a try. Thanks for any help in advance! Background: I have issues with my manual 2014 SP25GT. Since I drove it off the lot, it's had...

As the title says, I am getting a grinding noise coming from the transmission area after I replaced the clutch, flywheel, rear main seal, and axle seals. It has gotten progressivily worse and isnt tied to the Engine because it varies by car speed not engine RPM. Also the noise gets worse when...

I pulled my manual trans today to replace the rear main seal, RTV the MBSP bolts, and replace the clutch and flywheel. I pulled the trans, clutch, and flywheel and saw that the bearings were seized to s*** and left rusted metal dust everywhere. I inspected the trans shaft and it appears that it...

I will be replacing my clutch soon. Do I need to replace my flywheel along with the clutch? Also is there a guide for clutch replacement for the P5?

My wife drives a 2014 Mazda 5 Sport, 6 speed manual transmission, 34k miles and it recently started making a ticking sound when accelerating. I drove it tonight and the symptoms have changed a bit. So the ticking sound changes in frequency and tone as the engine revs, but if the clutch is...

Hello peers, I've been working on a 2010 Mazda 3 with the 2.5 liter and 6-speed manual. I've been meaning to boost this vehicle but as the tranny was a bit on the weaker side (152k hoonigan miles) I decided it would be wise to start with a fresher tranny. Anyways, fast-forward to last sunday, I...

Thanks for reading this and thanks more if you offer advice. I have a 2013 Euro Gen II Mazda diesel with a 6 speed manual - oh, and only 60,000 kms (35,000 miles)! I did see some other threads on this issue, but mostly under the Mazda 3. Does the Gen II Mazda 5 have the same "faulty slave...

Can anyone give me some advice on my wife's 2008 Mazda 5 Manual transmission? Clutch pedal randomly went to the floor today. No tension whatsoever, and no warning. I'm sure it's something with the master cylinder or slave cylinder, but I can't seem to locate either of them. Should I just cave...

Hello, fellow Mazda owners, I have a 2008 Mazda 2 1.3, I have had it for two years, and have finally decided to query an issue I've had for about the last year and a half, because my mechanic along with two other mechanics tell me that is just a "characteristic" of the car, but I am not buying...

My cruise control recently cut out. At first i attributed it to the LED tail light bulbs I was using but after installing load resistors with no change, it had to be something else. The other day my friend drove my car for the first time and accidentally tried to start it without the clutch...

I need a new clutch kit for my rx8 Where is best place to get one ? Can u trust a ebay one thats about $350? Helppppp

I have a 04 rx8 Tranny replaced month ago with used one. Before replaced had same problem I can shift in first soon as i goto shift into 2nd i get rpms to 3500 i press clutch in and theres like a grind when the clutch is in. Than i put it in second than same when u shift 2-3 3-4 but quiet...

...on my ride home from NYC to MD. I'm stuck in Jersey til I get it fixed. What am I in for here? Is Aamco gonna rake me over the coals? Thoughts? Suggestions? Thanks one and all!!

It's been getting slightly more difficult and rough to shift and downshift lately. But if I press the clutch all the way down with full pressure (minor work out to my left leg) then it's smoother to shift and feels very easy. Does this mean my clutch is going out. I just don't wanna have to...

Was on a 5 minute drive home (about a mile) from an appointment and I came to a stop to turn into my neighborhood. Once traffic passed I proceeded to turn and the transmission caught for a second, slipped, and then caught again. It made a loud grinding noise while it was slipping. I came to...

Background: 2012 Mazda5 Sport with 6-speed manual, dealer serviced only, currently about 26k miles on the odometer. Issue: when the clutch is depressed and released during a normal shift, there is a brief low noise as the clutch is released. It's almost like a "honk" or groan. Primarily in the...

Hey there, about last week i started to notice my 03 Protege started to become more difficult to shift into gears, however i dont get any resistance when going into 5th. It feel kind of 'notchy', when im halfway into gear i get the resistance then after giving a little more muscle it goes all...