I'm clearing out some of the stuff I have laying around...
First up, the Protege Garage FMIC
Will come with 2 IC cores - was going to replace the lower IC with the one with the red caps because I ran into a curb stop and the ambient air temp sensor bracket in the bumper skin crushed a few of the bottom fins (see close up pic). Pipes have normal wear and tear - worst is in the close up of rubbing mark. Tapped for Meth. Looking for - $350 shipped obo - SOLD
Next up, an older Tial Wastegate I ran for less than 1 year on my old '02 Nissan Maxima with a custom turbo setup. Has been sitting in a box for the last 3 years. IIRC, it is the F46 model. Includes 2 flanges and all bolts. Looking for - $250 shipped obo
Here's a rear trunk brace - a copy of the GT Spec version - works fine but I would replace the acorn nut for a better quality nut. This fits behind the rear bumper skin. Can install without removing bumper. Looking for - $50 shipped obo
Here's a 2.5" steel section with 3 1/8 NPT bungs welded in. Perfect for 1, 2 or 3 meth nozzles. I was going to place this in line with my PG FMIC kit (right after the IC outlet) but my new FMIC kit doesn't have enough slack in it to allow me to insert this inline and I had to tap the piping :-( Will also include the 3 black 1/8" NPT plugs. Pipe is bead rolled on each side to prevent coupler blow off. Looking for - $35 shipped obo
Here is a set of custom kick panel pods with tweeter and mid-range speaker installed. I bought this off some guy on M3F. Here is a copy of his original post:
To be honest, these things are pretty rough. You'll probably want to sand these down for a smoother finish and repaint them. They would be a great starting point for someone though. Looking to get what I paid - $150 shipped obo.
Finally, I have a used Greddy Profec E-01 Boost Controller for sale. Again, this was used for less than a year in my Maxima. It's been sitting in the same box as the wastegate for the last 3 years or so. It worked 100% when it was uninstalled. I do not have any paperwork or manual or box for it. You'll have to find those online. Also, one of the plugs looks like it's missing the housing to plug it into the brain module - see closeup pic. The wires are fine and the little pins are on it, just the housing I can't find. Also, looks like the screen has some light scratches from moving around in the box. Includes wired remote, pressure sensor and boost control solenoid and screen and brain box. New, this was over $550 - looking for $350 shipped obo.
Feel free to send me any questions and/or offers. Thanks! PayPal accepted.
First up, the Protege Garage FMIC
Will come with 2 IC cores - was going to replace the lower IC with the one with the red caps because I ran into a curb stop and the ambient air temp sensor bracket in the bumper skin crushed a few of the bottom fins (see close up pic). Pipes have normal wear and tear - worst is in the close up of rubbing mark. Tapped for Meth. Looking for - $350 shipped obo - SOLD
Next up, an older Tial Wastegate I ran for less than 1 year on my old '02 Nissan Maxima with a custom turbo setup. Has been sitting in a box for the last 3 years. IIRC, it is the F46 model. Includes 2 flanges and all bolts. Looking for - $250 shipped obo
Here's a rear trunk brace - a copy of the GT Spec version - works fine but I would replace the acorn nut for a better quality nut. This fits behind the rear bumper skin. Can install without removing bumper. Looking for - $50 shipped obo
Here's a 2.5" steel section with 3 1/8 NPT bungs welded in. Perfect for 1, 2 or 3 meth nozzles. I was going to place this in line with my PG FMIC kit (right after the IC outlet) but my new FMIC kit doesn't have enough slack in it to allow me to insert this inline and I had to tap the piping :-( Will also include the 3 black 1/8" NPT plugs. Pipe is bead rolled on each side to prevent coupler blow off. Looking for - $35 shipped obo
Here is a set of custom kick panel pods with tweeter and mid-range speaker installed. I bought this off some guy on M3F. Here is a copy of his original post:
redwrangler said:
To be honest, these things are pretty rough. You'll probably want to sand these down for a smoother finish and repaint them. They would be a great starting point for someone though. Looking to get what I paid - $150 shipped obo.
Finally, I have a used Greddy Profec E-01 Boost Controller for sale. Again, this was used for less than a year in my Maxima. It's been sitting in the same box as the wastegate for the last 3 years or so. It worked 100% when it was uninstalled. I do not have any paperwork or manual or box for it. You'll have to find those online. Also, one of the plugs looks like it's missing the housing to plug it into the brain module - see closeup pic. The wires are fine and the little pins are on it, just the housing I can't find. Also, looks like the screen has some light scratches from moving around in the box. Includes wired remote, pressure sensor and boost control solenoid and screen and brain box. New, this was over $550 - looking for $350 shipped obo.
Feel free to send me any questions and/or offers. Thanks! PayPal accepted.
Last edited:
