Search results

Hey guys, My 2000 1.6L standard protege used to get good mileage. I remember it was about 11.6 KM/L and 12 KM/L which is almost 30 MPG. That's what it is supposed to get. Now i seem to only be getting 8.75 KM/L which is around 20 MPG.... Now it is supposed to get 31 on highway and 25 in the...

Okay so an update. I fixed the noise on accelerating. I needed to torque up the axle nut more. Got a torque wrench and did it and that noise is gone. Most of the car is fixed now however i am still having an issue. When turning sometimes i have clunking or clicking noise. It happens much more...

No one has any ideas? I am thinking maybe they sent me the wrong axle or something because i did notice that the half shaft was thicker than the one that i pulled out of there. The drive train noise can be heard when applying gas or clutch and it seems to come from the axle hub area.

Hello Guys, I have a 2000 Protege 1.6L standard. It has 184500 KM on it. In the summer I replaced the clutch. It was harder than I had anticipated and I damaged the rubber boot on the outer CV joint on the driver’s side. I thought ohh I know I’ll need to fix it. So I priced the rubber boot and...

Alright well i fixed it. Basically i went to the wrecking yard and got the MAF sensor from a car there. He only charged me 20 and gave me the air filter with it for free since it was in pretty good shape and mine needed replacement. It was a bit of driving there but i popped it in once i got it...

K so two things. 1. I don't know anyone with another 1.6L protege and the MAF's are different for the different models so the aunt i have who has a 2.0 wont work. The wrecker has one from a 1.6L that has a broken tranny that he said he would sell me for 40$. I went and put the volt meter to the...

Okay i did some analysis on this and read the voltages out of the MAF sensor. What i did was took a 12v multimeter and accesses the 5 wires and read voltage. I did four tests. My theory is the Scanner tool is an easy way to access readings across the different systems of the car. However they...

The workshop manual also tells me i can test the voltage with a test light on the PCM terminals by tapping it into the wire. Im gonna do that tomorrow morning and go from there. It could very well be a MAF issue since one of the stripped screws was holding the MAF in place. Thanks

Well i read about a fuel filter issue so i popped the fuel hatch door from under the seats and looked inside and the mesh filter looks fine, so does theinside of the tank and all that. One strange thing i noticed was a gray connector that went to the back of the car that said "89" on it in a...

Well i took a look at the quick diagnostic chart in the workshop manual and it says the issues i am having: Buck/Jerk Misses Surges Hesitation/Stumble Is caused by three possible things, all listed are: Improper engine compression Improper Valve timing Poor fuel quality Could poor fuel...

The O I/M relates to the oxygen sensor and the EV is the EVAP system. The C is the Cataylist, which i expect is the catalytic converter.

K well i bought the manual. It is 1400 pages or something. I went to the diagnostic section and it has a list of steps for the issues i am having. Step 3 or 4 askes me to connect a reader and check some PID's. I also got a code reader the Innova 3020 and it shows no codes. However not all the...

Interestingly enough there is one bolt that holds on the coil that is snapped. I dunno who worked on this car but im not gonna drill it out as it is unnecessary. I fixed the one on the MAF which was messed, i think cause someone tried to pull it off. Anyways.

K so i checked the spark plugs and they were hurting hard. I replaced them and now the old ones look so bad compared to the new ones. I could post a pic but i don't think it matters. Regardless, i drove it again and the same issue apply. I thought about the spark plug wires also but haven't...

I've spent 25 mins looking and haven't found any free service manuals. Just the owners manual and it dosnt have a troubleshooting section. All the service manuals want me to put my credit card in and pay scrills and im not down for that. I can maybe find it later if i look more. Does anyone know...

I downloaded the manual and ON THE VERY FIRST PAGE IT SAYS "An authorized Mazda dealer knows your vehicle best. So when maintenance or service is necessary, thatfs the place to go" Wtf did they not proof read their manual??? Sorry i had to post this. Anyways i'm going to read this and hopefully...