Search results

Just a few left overs from my recent Mazdaspeed Protege. I'm located in Lemont, IL 60439 if anyone is interested in doing a pick up. For Sale: * Mid-pipe/J-pipe exhaust section - $ Make an offer, only pickup * Stock SMIC - $50 * Coldpipe - $15 * Lower Right Control Arm - $55 * Steering Column...

The bushing has gone bad on mine, so I'd rather just get the whole assembly. I also need the bolt which runs horizontal that clamps onto the lower section of the ball joint. Sorry for the wordings, but I couldn't find that part anywhere, believe its the pinch bolt??

Upgrading to a GRD built Audi TT, but I need to sell my speed Protege first. Just wondering, what do you guys think I should be asking? I'm from Illinois and I've seen some sell for around $8,000 with more miles and less mods. Car runs great, but has a few minor defects. I've listed some info on...

Recently, when I press and depress the clutch pedal it makes a squeaking noise(not coming from the trans, but the clutch pedal assembly). Is there a simple lube/grease fix for this problem? The pedal also is starting to get harder to press. Also, I had the master cylinder replaced last year...

Lately, I've been experiencing fuel cuts, I'm assuming because of the cold weather, when I try to go WOT or close to this. My current engine mods are SU SMIC, IC Pipes, J-pipe back Catless Exhaust, Stage Colder Plugs, SSAFC, and mbc set @ 9psi. Just wondering if there's something I need to be...

Wondering what I should get next for the MSP? I'm still craving more power and looking to spend around $500 more... Here's my current list of mods: Hasport Motor Mounts, SU Smic, Hardpipes, Joep MBC (@10psi), Catless J-pipe/ Midpipe, SSAFC v1, NGK -1 Plugs, and Prosport Boost Gauge. Thinking a...

Snapped my front end link, and went to replace, but I am having trouble installing the new end link (CORRECT PART, LENGTH, EtC.) The problem is the distance from the sway bar hole to the strut hole is too short. Soo I'm wondering if there are any tips/tricks to open this distance wider to get...

Snapped my front end link, and went to replace, but I am having trouble installing the new end link (CORRECT PART, LENGTH, EtC.) The problem is the distance from the sway bar hole to the strut hole is too short. Soo I'm wondering if there are any tips/tricks to open this distance wider to get...

Looking to buy a set of Tokico Struts in good condition. Preferably something that was taken off earlier in the car's life. I.e. - Less than 50k. PM with something and I'll make an offer. QUICK BUYER!!

Looking to buy 4 Tokico Struts for the MSP. Prefer a set that has less than 50k. PM me please!!

Just installed a 2.5" J-pipe/Mid-pipe, and a new axle-back portion on the MSP. I'm getting exhaust leaks because I didn't replace the gaskets, anyone know what I need and where I can get it? Assuming I need the gasket between down-pipe and j-pipe, midpipe and s-pipe, s-pipe and axle-back.

After installing my boost gauge last week, I noticed the CD player and Keyless Entry stopped working. I believe the problem started because I spliced the 12v red wire on back of the cd player to power my gauge (STUPID ME). To try and fix the problem, I disconnected the gauge and put everything...

Ok, tried posting a few times already, and did massive amounts of searching. However, I still haven't fixed my problem. I'll be more specific this time, hope this helps troubleshooting cuz the MSP isn't running right. **MSP was stock up until a few weeks ago, with no running or idle issues...

Last week I installed a new SMIC, SLS hot-pipe, custom cold-side pipe and Mid-pipe. After a few test runs, I noticed after the car is completely warm, when I shift into neutral the rpm's will dip to around 100-200 rpms and then recover back to 700. Wondering what protocol/troubleshooting areas I...

Installing a ETS side mount intercooler this weekend. I'm using some spare 2.25" intercooler piping for the cold-side and want everything to fit snug. What size silicone couplers/reducers do I need for the manifold and endtank? I thought the manifold size was 2.5" and the intercooler side was...

Problem: I live on a steep incline, and as of lately when I park: put the car in gear, pull the ebrake all the way up... I get out and the car seems like it wants to roll backwards and does a few inches sometimes. A mechanic (from a $ hungry shop) told me I need new rear calipers and e-brake...

Looking to get a split second afc.

Both my left and right rear calipers are going, need new or used ones asap. Otherwise the MSP might roll down the driveway again... (nailbyt)

Looking to purchase a midpipe with or without the J-pipe as well. I know SLS performance sells one, but I wanted to see if anyone else sells one.

For sale: Samco Sport - Intercooler hose kit for the MSP. Brand new, still in the package, waiting to be shipped. Asking $110 shipped. (bling) - SOLD!