Search results

I'm having trouble getting idle to settle down. I loosened the screw in the TB quite a bit and the car still wants to idle around 800 rpm (which is what i would like) but when the car gets hot (~92C water temp) it starts ocsillating and dies. If i hold the gas pedal down 2-3% it will idle just...

yes, I might be able to hook both the logworks software for the WB controller and the MT up at once...... Does anyone know what water temp the stock ecu turns on the fans? Idling in the driveway brought the water temp up to 92C and the fans never turned on. (i have the stock water temp sensor...

I have some good documents from Steve. Right now I just want to get the idle dialed in, make sure the fans are coming on, and take her out for a little spin to get afrs closer to 14.7. Right now the car seems to be running rich. I was mostly just wondering if anyone wanted to ride with me to...

tuning time...anyone want to help out??? Fond du Lac, WI......

medival? I just bought some from FL_mp5...

I ditched the adj cam gears but the above list is correct plus SRI, Thunder header, MAM midpipe with highflow cat, RB catback, stiffer valve springs, titanium retainers, lightweight underdrive crank pully, 9lb flywheel, welded MSP differential, spec stage two clutch, innovate LC-1 I tried...

SHE LIVES!!!! I had some of the crank sensor wiring messed up. Once that was fixed she fired up on the first try! idles semi-smoothly around 800-1000 with AFR's in the 12-13 range. Tomorrow I hope to get her on the road and try to dial in afrs a little better. I'm hopefully going to be...

I would buy one of those in a heartbeat!

Turns out my db9 to usb adapter was at fault for the 'no connection to ECU' hooked up the MT to the PC and connected instantly. My error was the water temp sensor. I just the LC-1 reprogrammed to send a wideband 0-5V signal to the MT as well. Talked to Turfburn a few times.... figured out my...

yes sir tried it with and without...same result, seems like it tries to connect then says no connection to ecu

Still not having any luck connecting the laptop to both the LC-1 and MT software. I think its the usb to DB9 adapter cable. I tried re-installing the drivers but no go. I will be trying some more experiments tonight... dragging the PC with built in serial ports out to the garage!!

Thanks guys, I am going to get a chance tonight to hook up the laptop and check the error codes. No smoke, or smelly burned capacitors...

MT rough install is complete.... green led is steady on, amber led is steady on, red led is blinking slow and steady. (really really hope that isnt a sign of death!) I am having trouble connecting my laptop to the MT. The MT software wants to link to COM1 or COM2 but my usb ports are COM5 and...

MT rough install is complete.... green led is steady on, amber led is steady on, red led is blinking slow and steady. (really really hope that isnt a sign of death!) I am having trouble connecting my laptop to the MT. The MT software wants to link to COM1 or COM2 but my usb ports are COM5 and...

^^ Is your grounding kit 4 or 8 gauge?

the rough MT install is about 75% complete, should be able to try and fire her up sometime this weekend.

I guess, I'm going to try and have the stock ecu control fuel. For the coolant temp sensor I meant a separate ground for the metal fitting that holds the sensor, since it is located in the middle of a rubber hose. I left the stock water temp alone as well. All i have left to hook up is 12V...

ok just spent the past 6 hr installing the MT (not quite done yet...) injectors --- done coolant temp sensor --- done (those with a second sensor, did you ground the housing?) air temp sensor --- done (also installed resistor) TPS --- done Coils --- done tach - ?? (grey blue wire) if the...

I dont know if FI peeps will get the same lope as NA guys with large overlap..... Mines pretty lopey

1. LordWorm (NA) 2. AusOrion (NA) 3. MZ_Zoom (FI) 4. Kayman (FI) 5. Sleepy (NA) 6. Crazee D (NA) 7. ctt 1982 (FI) 8. mazdaspeedweerx (FI) 9. Bala de Plata (FI) 10. jimmysuite (NA)